Endace DAG 4.2S Скачать руководство пользователя страница 6

Страница: 6 / 39

EDM01-02: DAG 4.2S Card User Guide

Version 7: May 2006

Chapter 1: Introduction

Introduction

The installation of the Endace DAG card on a PC begins with installing the

operating system and the Endace software.

Viewing this

document

This document, DAG 4.2S Card User Manual is available when the

installation CD is placed in a running Windows PC.

In this chapter

This chapter covers the following sections of information.

User Manual Purpose

DAG 4.2S Card Description

DAG 4.2S Card Architec

ure

DAG 4.2S Card Extended Functions

DAG 4.2S Card System Requirements

1.1 User Manual Purpose

Description

The purpose of this DAG Card User Manual is to describe:

Installing DAG 4.2S card

Setting Optical Power

DAG 4.2S Card Confidence Testing

Running Data Capture Software

Synchronizing Clock Time

Data Formats

Prerequisite

This document presumes the DAG card is being installed in a PC already

configured with an operating system.

A copy of Debian Linux 3.1 [Sarge] is available as a bootable ISO image

on one of the CD's shipped with the DAG card.

To install on the Linux/FreeBSD operating system, follow the instructions

in the document EDM04.06-01 Linux FreeBSD Installation Manual,

packaged in the CD shipped with the DAG card.

To install on a Windows operating system, follow the instructions in the

document EDM04.06-02 Windows Installation Manual, packaged in the

CD shipped with the DAG card.

Содержание DAG 4.2S








































Результаты поиска

Содержание DAG 4.2S

Отзывы:

Endace DAG 4.2S, Руководство пользователя, Страница: 6 / 39

Результаты поиска

Содержание DAG 4.2S

Отзывы: