Endace DAG 4.2S Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 39

Endace DAG 4.2S Скачать руководство пользователя страница 18

EDM01-02: DAG 4.2S Card User Guide

©2005

13

Version 7: May 2006

ATM status

In ATM mode, the status output changes:

dag@endace:~$ dagfour -d dag0 atm
light   laser nomuxfcl nomuxeql
link    ATM noreset OC48c fcl noeql
sonet   slave scramble
packetA drop=0
pci     66MHz 64-bit buf=128Mb rxstreams=1 txstreams=0 mem=128:0

For configuration options removing or adding the

no

prefix will change the

setting.

4.4 DAG 4.2S Card Configuration Options

Description

There are many DAG 4.2S card configuration options supported.

default

set framer to normal defaults

[no]laser

dis/enable transmit laser

atm

set framer into ATM mode

pos

set framer into Packet-over-SONET (PoS) mode

[no]muxfcl

(un)set facility loopback in the MUX

[no]muxeql

(un)set equipment loopback in the MUX

[no]reset

hold/release framer (in) reset

oc48c

set framer to OC48c mode

[no]fcl

(un)set facility loop back in the phy. This is

useful for card chaining

[no]eql

(un)set equipment loop back in the phy

[no]scramble

(un)set SONET scrambling

master

set card to SONET clock master

slave

set card to SONET clock slave

[no]pscramble

(un)set Packet-over-SONET scrambling

[non]discard

(un)set discard of FCS mismatched PoS packets

crc16

PoS CRC16 link

crc32

PoS CRC32 link

[no]pmin

dis/enable discard of packets smaller than a

predefined minimum size

[no]pmax

dis/enable discard of packets larger than a

predefined maximum size

[no]rxpkts

dis/enable packet reception

[no]txpkts

dis/enable packet transmission

[no]txrclk

dis/enable packet transmission

«
...
16
17
18
19
20
...
»

Содержание DAG 4.2S








































Отзывы:

Нет отзывов