background image

EDM01-02: DAG 4.2S Card User Guide 

©2005 

26 

Version 7: May 2006 

6.2.2 Two Cards no Reference Time Synchronization 

Description 

When two DAG cards are used in a single host PC with no reference 

clock, the cards are to be synchronized in some way if timestamps 

between the two cards are to be compared.  For example, if two cards 

monitor different directions of a single full-duplex link. 

 

Synchronization between two DAG cards is achieved in two ways.  One 

card can be a clock master for the second, or one can synchronise to the 

host and also act as a master for the second. 

 

Synchronizing 

cards 

If both cards are to be accurately synchronised, but not so for absolute 

time of packet time-stamps being correct, then one card is configured as 

the clock master for the other.  

 

Locking cards 

together 

Although the master card’s clock will drift against UTC, the cards are 

locked together.   

 

The cards are locked together by connecting the synchronisation connector 

ports of both cards with a standard RJ-45 Ethernet cross-over cable. 

 

Configure one of the cards as the master, the other defaults to being a 

slave. 

 

dag@endace:~$ dagclock –d dag0 none overout 
muxin   none 
muxout  over 
status  Not Synchronised Threshold 596ns Failures 0 Resyncs 0 
error   Freq 0ppb Phase 0ns Worst Freq 0ppb Worst Phase 0ns 
crystal Actual 100000000Hz Synthesized 67108864Hz 
input   Total 0 Bad 0 Singles Missed 0 Longest Sequence Missed 0 
start   Thu Apr 28 14:48:34 2005 
host    Thu Apr 28 14:48:34 2005 
dag     No active input - Free running

 

 

 

The slave card configuration is not shown, the default configuration is 

sufficient. 

 

 

Содержание DAG 4.2S








































Отзывы: