37173-5-1019
Page 11
WarninG
If you do not follow these instructions exactly, a fire or explosion may result causing property damage,
personal injury or loss of life.
to turn oFF Gas to aPPliance
For Your saFetY reaD BeFore liGHtinG
a. this appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instructions
exactly.
B. BeFore liGHtinG smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHat to Do iF You sMell Gas
•
Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your building.
•
immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
•
if you cannot reach your gas supplier, call the
fire department.
c. use only your hand to push in or turn the gas
control knob. never use tools. if the knob will not
push in or turn by hand, don't try to repair it; call
a qualified service technician. Force or attempted
repair may result in a fire or explosion.
D. Do not use this appliance if any part has been
under water. Immediately call a qualified service
technician to inspect the appliance and to replace
any part of the control system and any gas control
which has been under water.
1. Turn off all electric power to appliance if service is to
be performed (if applicable).
2. Remove control access panel (front panel).
3. Push in gas control knob slightly and turn clock-
wise
to "OFF." Do not force.
4. Replace control access panel (front panel).
liGHtinG instructions
1. STOP! Read the safety information above.
2. Turn off all electric power to the appliance
(if applicable).
3. Remove control access panel (front panel).
4. Push in gas control knob slightly and turn clockwise
to OFF.
note:
Knob cannot be turned from "PILOT" to "OFF"
unless knob is pushed in slightly. Do not force.
5. Wait ten (10) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas,
STOP! Follow "B" in the safety information above. If
you don't smell gas, go to the next step.
6. Remove the pilot access cover located on the
combustion chamber.
7. Find pilot - follow metal tube
from gas control. The pilot is
behind the pilot access cover.
8. Turn knob on gas control counterclockwise
to "PILOT."
9. Push in control knob all the way and hold in.
Immediately light the pilot with the Piezo Pilot Ignitor
or a match. Continue to hold the control knob in for
about one (1) minute after the pilot is lit. Release
knob, and it will pop back up. Pilot should remain
lit. If it goes out, repeat steps 5 through 10.
• If knob does not pop up when released,
stop and immediately call your service
technician or gas supplier.
• If the pilot will not stay lit after several tries,
turn the gas control knob to "OFF" and call
your service technician or gas supplier.
10. Replace pilot access cover.
11. Turn gas control knob counterclockwise
to "ON."
12. Replace control access panel (front panel).
13. Turn on all electric power to the appliance (if
applicable).
14.
caution:
Pilot access cover must be kept tightly
closed during operation.
liGHtinG instructions
PILOT
BURNER
THERMOPILE
Содержание DV-210
