Empire Comfort Systems DVP42FP30N-4, Инструкция по установке и руководство пользователя, Страница: 34 / 80

31455-10-1115 Page 34
NOTICE: For top vent installation only: Use of a DVA47 adap-
tor is required.
CAUTION : Sharp edges, use protective gloves when
installing.
Tools Needed for Installation:
Sheet metal snips
5/16” nut driver
3KLOOLSVKHDGVFUHZGULYHU
High temperature sealant or furnace cement rated for continuous
use at 1,000
o
F minimum
Measuring tape
3DUWV9HUL¿FDWLRQ
See parts list on page 36 to verify components included in this vent
kit prior to installation.
NOTICE: $'9$DGDSWRUPXVWEHXVHGLQFRQMXQFWLRQZLWKWKH
DVVK4RE (top vent connection only). See Figure 59.
NOTICE: ,ILQVWDOOLQJRQWRZRRGODSRUYLQ\OVLGLQJWKHYLQ\OVLGLQJ
kit should be used (sold separately, part number DV-822).
The vinyl siding vent kit, DV-822, is available from Empire Comfort
6\VWHPV ,QF 7KH GHSWK LV ´ PP ZKLFK HQDEOHV WKH YHQW
FDSWREHH[WHQGHGDZD\IURPYLQ\OVLGLQJRUSURMHFWLRQV7KHZDOO
depth plus the additional 3” (76mm) depth of the vinyl siding vent
cap extension should not exceed a total depth of 13 3/4” (349mm).
,I ZDOO GHSWK H[FHHGV ´ PP H[WHQG V\VWHP XVLQJ
6 5/8” (168mm) x 4” (102mm) rigid venting (See Fireplace Instruc-
tions for approved lengths)
See Figure 59.
Installing Wall Thimble/Firestop Assembly
)L[¿UHSODFHWRSHUPDQHQWORFDWLRQ,IXVLQJULJLGYHQWLQJV\VWHP
LQVWDOOXSWRWKHORFDWLRQZKHUHLWZLOOH[LWWKHEXLOGLQJ
&XWKROHLQZDOOIRUZDOOWKLPEOH¿UHVWRSDVVHPEO\
Figure 58 )
LQWR\RXUFRPEXVWLEOHZDOO1RWH2QEULFNRUEORFNH[WHULRUZDOO
a 7” (178mm) diameter hole needs to be cut.
0HDVXUHWKHWRWDOZDOOWKLFNQHVVWRGHWHUPLQHZKHWKHURUQRWWKH
H[WHQVLRQWKLPEOHLVWREHXVHG,IWKHFRPEXVWLEOHZDOOGHSWK
is over 5 3/8” (137mm), then the extension thimble should be
used.
See Figure 58.
,QVWDOOWKHZDOOWKLPEOHDVVHPEO\WKURXJKWKHIUDPHGRSHQLQJVR
WKH¿UHVWRSSODWHLVRQWKHLQWHULRUZDOO
Figure 58 ). Telescope
VHFWLRQ VKRXOG H[WHQG DOO WKH ZD\ WKURXJK WKH H[WHULRU ZDOO
$WWDFKZLWKIRXU[´VFUHZV
:KHQSODFLQJWKHYHQWFDSRQDQH[WHULRUZDOOFRYHUHGZLWK
FRPEXVWLEOHVVXFKDVZRRGODSRUYLQ\OVLGLQJLQVWDOOWKHYLQ\O
VLGLQJNLWWRWKHH[WHULRUZDOOVKHDWKLQJ
Figure 58
Figure 59
Cutting Vent Tubes
This is the most important part of the installation. With the
¿UHSODFHDQGWKHULJLGYHQWLQJV\VWHPLIXVHG¿[HGWRLWVSHUPD -
nent location, the 6 5/8” (168mm) diameter air inlet tube and the 4”
PPGLDPHWHUÀXHRXWOHWWXEHDUHWREHPDUNHGDQGFXWXVLQJ
WKHIROORZLQJSURFHGXUH
5. Attach the inlet tube to the outside mounting plate. Align
tinnerman clips on the tabs of the air inlet tube to the holes
RQRXWVLGHPRXQWLQJSODWHDQG¿[ZLWKWZR[´VFUHZV
:LWKWKHYLQ\OVLGLQJNLWLQVWDOOHGWRZDOOLIQHFHVVDU\LQVHUW
WKH´PPGLDPHWHUWXEHZLWKRXWVLGHPRXQWLQJSODWH
DWWDFKHGWKURXJKKROHLQZDOO&RQQHFWWRFROODURQ¿UHSODFHRU
ULJLGYHQWV\VWHP0HDVXUHEHWZHHQZDOORUYHQWFDSH[WHQVLRQ
and outside mounting plate. See Figures 60 and 61.
DVVK-4RE VENT KIT INSTALLATION INSTRUCTIONS