background image

24032-2-1008

Page 3

IMPORTANT SAFETY INFORMATION

Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.

DO NOT OPERATE THIS APPLIANCE WITHOUT GLASS FRONT PANEL INSTALLED

•  Due to high temperatures the appliance should be 

located out of traffic and away from furniture and 

draperies.

•  The glass front or any part removed for servicing 

the appliance must be replaced prior to operating 

the appliance. Work should be done by a qualified 

service person.

•  Keep burner and control compartment clean. 
•  Vent cap is hot while fireplace is in operation.
•  Installation  and  repair  should  be  done  by  a 

QUALIFIED SERVICE PERSON. The appliance 

should be inspected before use and at least annually 

by  a  qualified  service  person.  More  frequent 

cleaning may be required due to excessive lint from 

carpeting, bedding materials, etc. It is imperative 

that control compartments, burners and circulating 

air passageways of the appliance be kept clean.

•  DO NOT put anything around the fireplace that will 

obstruct the flow of ventilation air.

•  Clearance in accordance with local installation codes 

and the requirements of the gas supplier.

•  DO  keep  the  appliance  area  clear  and  free  from 

combustible material, gasoline and other flammable 

vapors and liquids.

•  DO examine venting system periodically and replace 

damaged parts.

•  DO make a periodic visual check of pilot and burners. 

Clean and replace damaged parts.

•  CAUTION:  The  glass  used  in  your  fireplace  is 

tempered glass. If the glass is cracked or damaged in 

any way, it should be replaced only with a complete 

glass frame assembly from Empire. See parts list on 

Page

 

30 for ordering.

•  DO NOT use this fireplace if any part has been under 

water. Immediately call a qualified service technician 

to inspect the heater and to replace any part of the 

control system and any gas control which has been 

under water.

•  Any safety screen or guard removed for servicing 

an appliance must be replaced prior to operating 

the appliance.

•  This  appliance  must  be  installed  on  a  flat,  solid, 

continuous surface (e.g. wood, metal, concrete). This 

may be the floor, or it may be raised up on a platform 

to enhance its visual impact. The appliance may be 

installed on carpeting, tile, wood flooring or other 

combustible material as the appliance's base extends 

the width and depth of the appliance.

•  Children and adults should be alerted to the hazards 

of high surface temperatures and should stay away 

to avoid burns or clothing ignition.

•  Young children should be carefully supervised when 

they are in the same room as the appliance.

•  Clothing or other flammable material should not be 

placed on or near the appliance.

•  Adequate accessibility clearances for servicing and 

proper operation.

•  This appliance must not share or be connected to a flue 

serving a separate solid-fuel burning appliance.

•  Keep  the  area  around  your  appliance  clear  of 

combustible materials, gasoline and other flammable 

vapor and liquids. 

•  Under no circumstances should any solid fuels (wood, 

coal, paper or cardboard etc.) be used in this appli-

ance.

•  The flow of combustion and ventilation air must not 

be obstructed in any way.

Содержание DVP30CA30B-N1









































Отзывы: