Empire Comfort Systems DLCX36SP93N-1 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 52

Empire Comfort Systems DLCX36SP93N-1 Скачать руководство пользователя страница 30

29004-0-0711

Page 30

Figure

33

A = *Clearance above grade, veranda, porch, deck or balcony

[*12 inches (30cm) minimum]

B = clearance to window or door that may be opened [*12 inches

(30cm) minimum for appliances < 100,000 Btuh (30kW)

C = clearance to permanently closed window [minimum 12 inches

(30cm) recommended to prevent condensation on window]

D = vertical clearance to ventilated soffit located above the terminal

within a horizontal distance of 24 inches (60 cm) from the

center of the terminal [18 Inches (46 cm) minimum

E = clearance to unventilated soffit [12 inches 30cm) minimum]

F = clearance to outside corner.

See

Page

32.

G = clearance to inside corner.

See

Page

32.

H = *not to be installed above a meter/regulator assembly

within 3 feet (90cm) horizontally from the center-line of the

regulator

I = clearance to service regulator vent outlet [*6 feet (1.8m)

minimum]

J = clearance to non-mechanical air supply inlet to building or

the combustion air inlet to any other appliance [*12 inches

(30cm) minimum for appliances ≤ 100,000 Btuh (30 kW)

36 inches (90cm) minimum for appliances > 100,000 Btuh

(30kW)]

K = clearance to a mechanical air supply inlet [* 6 feet (1.8m)

minimum]

L = †clearance above paved sidewalk or a paved driveway located

on public property [*7 feet (2.1m) minimum]

M = clearance under veranda, porch, deck, or balcony [*12 inches

(30cm) minimum]

†

a vent shall not terminate directly above a sidewalk or paved driveway which

is located between two single family dwellings and serves both dwellings*

¥

only permitted if veranda, porch, deck, or balcony, is fully open on a minimum

of 2 sides beneath the floor*

*

as specified in CGA B149 Installations Codes or ANSI Z223.1. Note: Local

Codes or Regulations may require different clearances.

vENT CLEARANCES

«
...
28
29
30
31
32
...
»

Содержание DLCX36SP93N-1





















































Отзывы:

Нет отзывов