Empire Comfort Systems DLCX36SP93N-1 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 52

Empire Comfort Systems DLCX36SP93N-1 Скачать руководство пользователя страница 15

29004-0-0711

Page 15

Locating Fireplace

Before setting fireplace into the framed opening, attach the framing

brackets to the fireplace and secure to framing. The framing brackets

may be installed on the fireplace in the flat state. Once the fireplace

is placed into the framed opening, the brackets can be hand bent

over the framing and secured. This allows the fireplace to be

inserted into the pre-framed opening. Different hole locations can

be used for finishing materials with thicknesses of 3/8", 1/2" and

3/4". Secure the brackets with screws provided using two (2) per

framing bracket.

See

Figure

9.

Framing brackets should fit directly against framing material. Use

at least one (1) nail or screw per bracket to secure in place.

IMpORTANT!

Check squareness of all openings of the fireplace

prior to securing to the framed openings.

See

Figure

10.

Figure

9

Figure

10

FIREpLACE INSTALLATION INSTRUCTIONS (continued)

NAIL OR OTHER

SUITABLE FASTENER

FRAMING

CHECK TO SEE THAT

FIREBOX IS SQUARE PRIOR

TO ATTACHING TO FRAMING

WARNING: WHEN FINISHING THE FIREpLACE, NEvER

OBSTRUCT OR MODIFY THE AIR INLET/OUTLET

OpENINGS IN ANY MANNER. pROvIDE ADEqUATE

CLEARANCES AROUND AIR OpENINGS.

CAUTION: pRIOR TO INSTALLATION, MEASURE THE

F I R E p L A C E A N D v E R I F Y F R A M I N G

REqUIREMENTS, METHODS, AND WALL

COvERING DETAILS pRIOR TO FRAMING

CONSTRUCTION.

Surround Installation

To complete the installation of the fireplace, a Surround Kit

specifically designed for use with this fireplace must be installed

prior to use. Surround options shown on page 48 are available from

your dealer. Follow the instructions included with the Surround Kit

for proper installation.

«
...
13
14
15
16
17
...
»

Содержание DLCX36SP93N-1





















































Отзывы:

Нет отзывов