Empire Comfort Systems DLCX36SP93N-1 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 52

Empire Comfort Systems DLCX36SP93N-1 Скачать руководство пользователя страница 19

29004-0-0711

Page 19

SEE GRAPH FOR PERMISSIBLE “H” AND “V” DIMENSIONS

FIRESTOP AT
CEILING LEVEL

Figure

17

Examples of possible venting systems using two (2) 90° elbows.

V is listed as minimum vertical dimensions and H1 + H2 is the total

of maximum horizontal dimensions. The maximum vertical and

horizontal distances for two (2) 90° elbows as shown in Figure 18

is 20 feet.
Attention: Refer to Figures 19-21 for additional venting

requirements.

FIRESTOP AT
CEILING LEVEL

1

SEE GRAPH FOR PERMISSIBLE “H” AND “V” DIMENSIONS

NOTE: H1 AND H2 MUST BE ADDED TOGETHER TO USE CHART

Figure

18

Below Grade Installation

When it is not possible to meet the required vent terminal clearances

of 12" (305mm) above grade level, a snorkel kit is recommended. See

Figures 41a and 41b . It allows installation depth down to 7" (178mm)

below grade level. The 7" (178mm) is measured from the center of

the horizontal vent pipe as it penetrates through the wall.

Ensure the sidewall venting clearances are observed. If venting

system is installed below ground, we recommend a window well

with adequate and proper drainage to be installed around the

termination area.

COMBUSTIBLE
PROJECTION

18” (457mm)

MINIMUM

12” (305mm)

ABOVE GRADE

48”

(1219mm)

PIPE STRAP

3” (76mm)

MINIMUM

TYpICAL BASEMENT INSTALLATION

Figure

16

Examples of possible venting systems using one (1) 90° elbow.

Eight (8) feet is listed as minimum vertical vent run with 20 feet of

maximum horizontal vent run. Vertical dimensions are based on

centerline to centerline of pipe. Horizontal dimensions are based

on centerline of pipe to end of termination.

vENTING FIREpLACE - TOp (continued)

«
...
17
18
19
20
21
...
»

Содержание DLCX36SP93N-1





















































Отзывы:

Нет отзывов