Empire Comfort Systems DLCX36SP93N-1 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 52

Empire Comfort Systems DLCX36SP93N-1 Скачать руководство пользователя страница 12

29004-0-0711

Page 12

In planning the installation for the fireplace, determine where the

unit is to be installed and whether optional accessories are desired.

Gas supply piping should also be planned at this time. A gascock

shutoff must be installed in this line.

The fireplace can be mounted on any of these surfaces:

1. A flat hard combustible or non-combustible surface.

2. A raised platform of combustible or non-combustible material.

3. Four (4) corners of the fireplace so contact is made on all four

perimeter edges on the bottom of the unit.

(Example: Four (4) concrete masonry blocks.)

If the fireplace is installed directly on carpeting, tile or other

combustible material other than wood flooring, install the

fireplace on a metal or wood panel extending the full width

and depth of the unit.

At this point, you should have decided what components to include

in your installation, and where the fireplace is to be located. If this

has not been done, stop and consult your dealer for assistance

with this planning.

pLANNING INSTALLATION

«
...
10
11
12
13
14
...
»

Содержание DLCX36SP93N-1





















































Отзывы:

Нет отзывов