Empire Comfort Systems DLCX36SP93N-1 Скачать руководство пользователя страница 25

Страница: 25 / 52

29004-0-0711

Page 25

17. To attach the vent connections at the fireplace, be sure the 7”

diameter adapter collar has been installed per step 3. Apply a

bead of silicone sealant to the 4” diameter flex connector, then

slide the flex pipe adapter collar into the fireplace flue collar

and secure by installing a minimum of two (2) screws through

the flue collar and into the adapter.

See

Figure

26.

18. Apply sealant to the 7” diameter adapter collar, slide outer

flex vent over the collar, then secure with a 7” diameter band

clamp.

See

Figure

26.

19. Once the lower connections are made and the flex pipe is

secured with support bands as required (3 feet minimum be-

tween supports) then the roof flashing can be installed.

See

Figure

27.

20. Install the roof flashing, and seal using common constructions

practices.

21. An additional storm collar band is provided in kit that may be

used as an attic insulation shield. The collar can be installed

around the flex pipe (or hard pipe) just above the firestop

thimble. This collar will act as a shield to prevent blown insu-

lation from entering the thimble.

22. To complete the vent installation, install the vent termination

cap to the top of the hard vent pipe assembly. Mate up the

flue and outer telescopes with the hard pipe assembly, then

secure by installing a minimum of two (2) sheet metal screws

into the overlapped flanges of the cap and pipe.

23. Figure 28

shows a completed installation with components

identified and other installation information such as heights

and clearance to combustibles.

Vent Cap

Storm

Minimum

Clearance to

Combustibles

Collar

Exterior

Roof

Flashing

Support

Roof

Assembly

7"(178mm) Dia.

Must Extend

7"(178mm) Dia.

Hard Pipe

Through Roof

Flashing

1” (25mm)

Flex

Figure

DvvK-4Fv DIRECT vENT TERMINATION KIT (continued)

Содержание DLCX36SP93N-1





















































Результаты поиска

Содержание DLCX36SP93N-1

Отзывы:

Empire Comfort Systems DLCX36SP93N-1, Инструкция по установке и руководство пользователя, Страница: 25 / 52

Результаты поиска

Содержание DLCX36SP93N-1

Отзывы: