Empava EMPV-24WO08 Скачать руководство пользователя

Страница: 16 / 22

GENERAL INFORMATION

Installation must conform with local codes or, in the

absence of local codes, with the National Fuel Gas Code,

ANSI Z223.1-Latest Edition.

WARNING!!

This appliance shall not be used for space heating. This

information is based on safety considerations.

3. AlI openings in the wall behind the appliance and in the floor

under the appliance shall be sealed.

4. Keep appliance area clear and free from combustible materials,

gasoline, and other flammable vapors.

5. Do not obstruct the flow of combustion and ventilation air.

6. Disconnect the electrical supply to the appliance before

servicing.

7. When removing appliance for cleaning and/or service;

  A. Shut off gas at main supply.
  B. Disconnect AC power supply.
  C. Disconnect gas line to the inlet pipe.

D. Carefully lift appliance out of cabinet cutout.

CAUTION

: Use care in handling.

Electrical Requirement

Electrical installation should comply with national and local

codes.

Air Supply and Ventilation

The installer must refers to local/national codes.

10.

Gas Manifold Pressure

Natural gas - 4.0” W.C.P.

11. The misuse of oven door (e.g. stepping, sitting, or leaning on

them) can result in potential hazards and/or injuries.

WARNING!!

ELECTRICAL GROUNDING INSTRUCTIONS

The oven must be electrically grounded in accordance with

local codes or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA No 70-latest edition.

Installation should be made by a Iicensed electrician.

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED.

This appliance is equipped with a three-prong grounding plug

for your protection against shock hazard and should be plugged

directly into a properly grounded socket. Do not cut or remove

the grounding prong from the plug.

For personal safety, this appliance must be properly

grounded.
Do not under any circumstances cut or remove the third

(ground) prong from the power plug.

REPLACEMENT PARTS

Only authorized replacement parts may be used in performing

service on the oven. Replacement parts are available from

factory authorized parts distributors. Contact the nearest parts

distributor in your area.

Содержание EMPV-24WO08























Результаты поиска

Содержание EMPV-24WO08

Отзывы:

Похожие инструкции для EMPV-24WO08

Бренды по названию

Популярные бренды

Empava EMPV-24WO08, Руководство по эксплуатации для пользователя

Результаты поиска

Содержание EMPV-24WO08

Отзывы:

Похожие инструкции для EMPV-24WO08

Бренды по названию

Популярные бренды