Emerson Rosemount Oxymitter DR Скачать руководство пользователя страница 60

Страница: 60 / 98

Figure 4-3: Cell Replacement Kit

A. Probe tube (not included in kit)

B. Calibration gas passage

C. Socket head cap screws

D. Cell and flange assembly

E. Corrugated seal

Procedure

1. Follow the instructions in

Remove probe

to remove the probe from the stack or

duct.

2. If the probe uses a snubber diffuser, use a spanner wrench to remove the flame

arrestor/snubber diffuser assembly.

3. Remove the locking set screw from the flame arrestor. Use spanner wrenches from

the probe disassembly kit (

Table 4

) to turn the flame arrestor hub free from the

probe flange. If equipped with the flame arrestor with ceramic diffuser, remove and
discard the setscrews and remove the vee deflector (

Figure 4-4

). Inspect the

ceramic diffuser. If damaged, replace using the element.

Note

The flame arrestor and flame arrestor hub are among the critical components of
this type of protection. See

Safety Data Sheet 1A99078

Maintenance and service

Reference Manual

October 2019

00809-0100-4880

Emerson.com/Rosemount

Содержание Rosemount Oxymitter DR



































































































Результаты поиска

Содержание Rosemount Oxymitter DR

Отзывы:

Бренды по названию

Популярные бренды

Emerson Rosemount Oxymitter DR, Справочное руководство

Результаты поиска

Содержание Rosemount Oxymitter DR

Отзывы:

Бренды по названию

Популярные бренды