Emerson Rosemount Oxymitter DR Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 98

background image

Fieldbus communications. See

Upgrade Rosemount

Oxymitter DR to full Oxymitter

for

upgrade information.

1.3

Probe options

1.3.1

Diffusion elements

Ceramic diffusion assembly

The ceramic diffusion assembly is the traditional design for the probe.

Used for over 25 years, the ceramic diffusion assembly provides a greater filter surface
area. This element is also available with a flame arrestor and with a dust shield to use with
an abrasive shield.

Figure 1-3: Ceramic Diffusion Assembly

Flame arrestor snubber diffusion assembly

The snubber diffusion assembly is satisfactory for most applications. This element is also
available with a dust seal for use with an abrasive shield.

Figure 1-4: Flame Arrestor Snubber Diffusion Assembly

Description and specifications

Reference Manual

October 2019

00809-0100-4880

18

Emerson.com/Rosemount

«
...
16
17
18
19
20
...
»

Содержание Rosemount Oxymitter DR



































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount Oxymitter DR

Бренд: Idexx Страницы: 6

Бренд: IDEAL INDUSTRIES Страницы: 10

Бренд: M-system Страницы: 5

Бренд: Flytec Страницы: 2

GroundCast DRS611

Бренд: Vaisala Страницы: 12

Бренд: DAKOTA ULTRASONICS Страницы: 50

Бренд: Jamar Страницы: 4

Бренд: UEi Страницы: 5

Бренд: Magnescale Страницы: 36

Бренд: Magnescale Страницы: 2

Бренд: IFM Страницы: 45

AMI INSPECTOR Hydrogen

Бренд: Swan Analytical Instruments Страницы: 74

Xevo TQ-XS Mass

Бренд: Waters Страницы: 213

Nunes Instruments Propeller Type Water Current...

Бренд: V-tech Страницы: 19

Бренд: ATI Technologies Страницы: 70

Бренд: MFJ Страницы: 5

Бренд: Koso Страницы: 25

Бренд: Tektronix Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды