Emerson Rosemount CT5100 Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 179

background image

2. Open the door of the electrical compartment.
3. Tag or otherwise identify all wiring harnesses before disconnecting.
4. Disconnect the 12 V power wiring harness (E) from the peripheral board (A).

NOTICE

The other end of the 12 V power wiring harness (H) is connected to connector J11
on the motherboard.
A ribbon cable (E) that connects the TEC board to the motherboard runs across the
top of the peripheral board and is secured with a cable tie (C) to the connector of
the ribbon cable (B) that plugs into the peripheral board.

5. Cut the cable tie (C) that secures the TEC board ribbon cable (E) to the connector of

the peripheral board ribbon cable (B). Carefully move the TEC board ribbon cable
clear of the peripheral board.

6. Disconnect the peripheral board ribbon cable (B) from the peripheral board.
7. Disconnect the relay wiring harness (I) from the peripheral board.
8. Disconnect the three connectors (J, K, and L) of the gas/cell temperature

monitoring harness from the peripheral board.

9. Remove and retain the four screws (H) and associated spring washers (G) and flat

washers (F).

10. Remove and discard the peripheral board.
11. Place the peripheral board (A) in position on the backplate.
12. Secure the peripheral board by fitting the four screws (H) and the associated spring

washers (G) and flat washers (F) retained during the removal procedure.

13. Torque tighten the screws to 0.6 Nm.
14. Connect the three connectors (J, K, and L) of the gas/cell temperature monitoring

harness to, respectively, connectors J9, J24, and J37 on the peripheral printed circuit
card (PCC).

15. Connect the relay wiring harness (I) to the peripheral board.
16. Connect the peripheral board ribbon cable (B) to the peripheral board.
17. Secure the TEC board ribbon cable (D) to the connector of the peripheral board

ribbon cable (B) with a cable tie (C).

18. Connect the 12 V power wiring harness (E) to the peripheral board (A).
19. Close the door of the electrical compartment and restart the analyzer.

Repair and replacement

Reference Manual

October 2019

00809-0100-4512

136

Rosemount CT5100(Ex)

«
...
134
135
136
137
138
...
»

Содержание Rosemount CT5100




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount CT5100

Бренд: Yamaha Страницы: 3

Бренд: Parr Instrument Company Страницы: 130

Бренд: jenway Страницы: 17

Бренд: jablotron Страницы: 2

Бренд: FISCHER Страницы: 20

Бренд: Kipp & Zonen Страницы: 32

Бренд: Sonel Страницы: 84

Бренд: Ratek Страницы: 25

Бренд: Osaka Страницы: 3

Бренд: SIKA Страницы: 8

Бренд: GAGEMAKER Страницы: 36

Бренд: BANTE Страницы: 17

Бренд: E+E Elektronik Страницы: 4

Бренд: yellow jacket Страницы: 16

Бренд: b&o Страницы: 32

Бренд: EIJKELKAMP Страницы: 11

Бренд: GE Страницы: 16

Бренд: Underground Magnetics Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды