Emerson Rosemount CT5100 Скачать руководство пользователя страница 122

Страница: 122 / 179

11.8

Visual examination

If the BIST fails to identify the problem, the next step is a visual examination of the
Rosemount CT5100(Ex).

Procedure

1. Open the door of the electrical compartment and remove the top cover.

Refer to

Removing the top cover

2. Visually examine the exterior of the analyzer for signs of damage.
3. Perform a visual inspection of the optical and electrical components inside the

analyzer.
Refer to

Figure 3-5

4. If any loose connections are found in the electrical compartment, refer to the wiring

diagrams (

Engineering drawings

) to identify and repair the connection.

5. Refit the top cover and close the electrical compartment door.

11.9

Functional failure diagnostics

If the Built-in-Self Test and the visual examination fail to identify the fault, perform the
failure diagnostics and recommended actions.

11.9.1

No illuminated LEDs on Power supply unit (PSU) when
analyzer switched ON.

Recommended actions

1. Check mains power is available.
2. If OK, replace PSUs.

11.9.2

Nothing powers up when connected to mains

Recommended actions

1. Check AC fuses (number 1 and number 2)
2. Replace if necessary.

11.9.3

Only MOXA and BEKA powers up

Condition

The startup screen displays BEKA; all other electronic modules remain unpowered.

Recommended actions

1. Check the 12 V PSU is working (LED illuminated).
2. If the 12 V PSU is not working, replace it.

Troubleshooting and diagnostics

Reference Manual

October 2019

00809-0100-4512

122

Rosemount CT5100(Ex)

Содержание Rosemount CT5100




















































































































































































Результаты поиска

Содержание Rosemount CT5100

Отзывы:

Emerson Rosemount CT5100, Справочное руководство, Страница: 122 / 179

Результаты поиска

Содержание Rosemount CT5100

Отзывы: