Emerson Rosemount 2051 Скачать руководство пользователя страница 96

Страница: 96 / 228

Reference Manual

00809-0100-4107, Rev BA

Section 6: Troubleshooting

April 2013

Troubleshooting

6.3.3

Diagnostic message: Advisory

Table 6-4. Status: Advisory

Alert name

LCD
screen

LOI screen Problem

Recommended action

Non-Critical

User Data

Warning

MEMRY

WARN

MEMORY

WARN

A user written parameter
does not match
expected value.

Confirm and correct all parameters

listed in Device Information.

Perform a Device Reset.

Replace Electronics Board.

Sensor

Parameter

Warning

A user written parameter
does not match
expected value.

Confirm and correct all parameters

listed in Device Information.

Perform a Device Reset.

Replace pressure sensor.

LCD Display

Update Failure

[If display

is not

updating]

[If display

is not

updating]

The LCD Display is not
receiving updates from
the pressure sensor.

Check the connection between the

LCD and the circuit board.

Replace the LCD Display.

Replace the electronics board.

Configuration

Changed

[none]

A recent change has
been made the device by
a secondary HART
master such as a
handheld device.

Verify that the configuration change

of the device was intended and
expected.

Clear this alert by selecting Clear

Configuration Changed Status.

Connect a HART master such as AMS

Device Manager or similar which will
automatically clear it.

Analog

Output Fixed

ANLOG

FIXED

ANALOG

FIXED

The analog output is
fixed and does not
represent the process
measurement. This may
be caused by other
conditions in the device,
or because the device
has been set to loop test
or multidrop mode.

Take action on any other notifications

from the device.

If the device is in loop test, and should

no longer be, disable or momentarily
remove power.

If the device is in multidrop mode and

should not be, re-enable loop current
by setting the polling address to 0.

Simulation
Active

[none]

The device is in
simulation mode and
may not be reporting
actual information.

Verify that simulation is no longer

required.

Disable simulation mode in service

tools.

Perform a Device Reset.

Содержание Rosemount 2051





































































































































































































































Результаты поиска

Содержание Rosemount 2051

Отзывы:

Похожие инструкции для Rosemount 2051

Бренды по названию

Популярные бренды

Emerson Rosemount 2051, Справочное руководство

Результаты поиска

Содержание Rosemount 2051

Отзывы:

Похожие инструкции для Rosemount 2051

Бренды по названию

Популярные бренды