manualshive.com logo in svg

Emerson Rosemount 2051, Справочное руководство, Страница: 67 / 228

Поделиться
Скачать
Emerson Rosemount 2051 Скачать руководство пользователя страница 67

57

Reference Manual 

00809-0100-4107, Rev BA

Section 4: Electrical Installation

April 2013

Electrical Installation

4.4.4

Local Operator Interface Password

A Local Operator Interface Password can be entered and enabled to prevent review and 
modification of device configuration via the LOI.  This does not prevent configuration from HART 
or external keys (analog zero and span; Digital Zero Trim).  The LOI password is a 4 digit code 
that is to be set by the user.  If the password is lost or forgotten the master password is “9307”.

The LOI password can be configured and enabled/disabled by HART communication via a Field 
Communicator, AMS Device Manager, or  the LOI.

Configuring LOI password with Field Communicator

Configuring LOI password with AMS Device Manager

1.

Right click on the device and select 

Configure.

2.

Under 

Manual Setup

 select the 

Security

 tab.

3.

Within the 

Local Operator Interface

 click the 

Configure Password

 button and follow the 

screen prompts.

Configuring LOI password using Local Operator Interface

Figure 4-3. Local Operator Interface password

4.5

Setting Transmitter alarm

On the electronics board is an alarm switch, reference 

Figure 4-2 on page 55

 for switch location. 

Follow the steps below to change the alarm switch location.

1.

Set loop to manual and remove power.

2.

Remove transmitter housing cover.

3.

Use a small screwdriver to slide switch to desired position.

4.

Replace transmitter cover; cover must be fully engaged to comply with explosion proof 
requirements.

From the 

HOME

 screen, enter the fast key sequence 

Device Dashboard Fast Keys

2, 2, 6, 5, 2

EXTENDED MENU

CALIBRAT
DAMPING
TRANSFER FUNCT
SCALED VARIAB
ASSIGN P
TAG
ALARM SAT VALUES

PASSWORD

PASSWORD

SIMULATE
HART REV
BACK TO MENU
EXIT MENU

PASSWORD

PASSWORD ENABLE
CHANGE PASSWORD
BACK TO MENU
EXIT MENU

VIEW CONFIG
ZERO TRIM
UNITS
RERANGE
LOOP TEST
DISPLAY

EXTENDED MENU

EXTENDED MENU

EXIT MENU

Содержание Rosemount 2051





































































































































































































































Отзывы:

Нет отзывов