Emerson Rosemount 2051 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 228

background image

67

Reference Manual

00809-0100-4107, Rev BA

Section 5: Operation and Maintenance

April 2013

Operation and Maintenance

The Sensor Calibration and the Analog Output Calibration combine to match the transmitter’s
measurement system to the plant standard.

Calibrate the sensor



Sensor Trim (



Zero Trim (

Calibrate the 4-20 mA output



4-20 mA/ 1-5V Output Trim (

)



4-20 mA/ 1-5V Output Trim using other scale (

5.4.1

Determining necessary Sensor Trims

Bench calibrations allow for calibrating the instrument for its desired range of operation.
Straight forward connections to pressure source allow for a full calibration at the planned
operating points. Exercising the Transmitter over the desired pressure range allows for
verification of the analog output.

Trim the pressure signal on page 71

discusses how the trim

operations change the calibration. It is possible to degrade the performance of the transmitter
if a trim is done improperly or with inaccurate equipment. The transmitter can be set back to
factory settings using the Recall Factory Trim command in

Recall Factory Trim—sensor trim on

.

For transmitters that are field installed, the manifolds discussed in

Rosemount 305, 306, and

304 Manifolds on page 51

allow the differential transmitter to be zeroed using the zero trim

function. Both 3-valve and 5-valve manifolds are discussed. This field calibration will eliminate
any pressure offsets caused by mounting effects (head effect of the oil fill) and static pressure
effects of the process.

Determine the necessary trims with the following steps.

1.

Apply Pressure

2.

Check digital pressure, if the digital pressure does not match the applied pressure,
perform a digital trim. See

Perform a Sensor Trim on page 72

3.

Check reported analog output against the live analog output. If they do not match,
perform an analog output trim. See

Performing Digital-to-Analog Trim (4-20mA/ 1-5 V

Output Trim) on page 75

Trimming with configuration buttons

Local configuration buttons are external buttons located underneath the top tag of the
transmitter. There are two possible sets of local configuration buttons that can be ordered and
used to perform trim operations: Digital Zero Trim and Local Operator Interface. To access the
buttons, loosen screw and rotate top tag until buttons are visible.



Local Operator Interface (M4):

Can perform both digital Sensor Trim and the 4-20mA

Output Trim (analog output trim). Follow the same procedures listed in trimming with
Field Communicator or AMS Device Manager listed below.



Digital Zero Trim (DZ):

Used for performing a sensor zero trim. See

calibration frequency on page 68

for trim instructions.

«
...
75
76
77
78
79
...
»

Содержание Rosemount 2051





































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 2051

Masoneilan 12400 Series

Бренд: Baker Hughes Страницы: 81

Бренд: Keller Страницы: 6

Бренд: ZHYQ Страницы: 6

HF scientific AccUView LED

Бренд: Watts Страницы: 40

Бренд: Valcom Страницы: 1

Бренд: PCB Piezotronics Страницы: 15

Бренд: Hach Страницы: 4

Бренд: Keithley Страницы: 338

Бренд: Ecodhome Страницы: 12

Бренд: Ress Страницы: 11

Бренд: Kedida Страницы: 4

Бренд: Fluke Страницы: 134

Бренд: Huazheng Страницы: 8

Бренд: Omega Страницы: 12

Бренд: janitza Страницы: 92

Бренд: TA Instruments Страницы: 68

ULTRACOLD 2WR6 Series

Бренд: Landis+Gyr Страницы: 21

Бренд: Resonance Technology Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды