manualshive.com logo in svg

Emerson Rosemount 2051, Справочное руководство, Страница: 83 / 228

Поделиться
Скачать
Emerson Rosemount 2051 Скачать руководство пользователя страница 83

73

Reference Manual 

00809-0100-4107, Rev BA

Section 5: Operation and Maintenance

April 2013

Operation and Maintenance

Performing a Sensor Trim with AMS Device Manager

Right click on the device and, under the 

Method

 drop down menu, move cursor over 

Calibrate

 

and, under 

Sensor Trim

, select 

Lower Sensor Trim

.

1.

Follow the screen prompts to perform a Sensor Trim using AMS Device Manager.

2.

If desired, right click on the device and under the 

Method

 drop down menu, move 

cursor over 

Calibrate

 and under 

Sensor Trim

 and select 

Upper Sensor Trim

Performing a Sensor Trim using Local Operator Interface

Perform an upper and lower Sensor Trim by referencing 

Figure 5-3

.

Figure 5-3. Sensor Trim with Local Operator Interface

Performing a Digital Zero Trim (option DZ)

A Digital Zero Trim (option DZ) provides the same function as a zero/lower Sensor Trim, but can 
be completed in hazardous areas at any given time by simply pushing the Zero Trim button 
when the transmitter is at zero pressure.  If the transmitter is not close enough to zero when the 
button is pushed, the command may fail due to excess correction.  If ordered, a Digital Zero Trim 
can be performed by utilizing external configuration buttons located underneath the top tag of 
the transmitter, see 

Figure 5-1 on page 68

 for DZ button location.

1.

Loosen the top tag of the transmitter to expose buttons.

2.

Press and hold the Digital zero button for at least two seconds, then release to perform 
a Digital Zero Trim. 

5.5.3

Recall Factory Trim—sensor trim

The Recall Factory Trim—Sensor Trim command allows the restoration of the as-shipped factory 
settings of the Sensor Trim. This command can be useful for recovering from an inadvertent zero 
trim of an absolute pressure unit or inaccurate pressure source. 

EXTENDED MENU

CALIBRAT

CALIBRAT

DAMPING
TRANSFER FUNCT
SCALED VARIAB
ASSIGN PV
TAG
ALARM SAT VALUES
PASSWORD
SIMULATE
HART REV
BACK TO MENU
EXIT MENU

VIEW CONFIG
ZERO TRIM
UNITS
RERANGE
LOOP TEST
DISPLAY

EXTENDED MENU

EXTENDED MENU

EXIT MENU

CALIBRAT

ZERO TRIM

LOWER TRIM

LOWER TRIM

UPPER TRIM

UPPER TRIM

ANALOG TRIM
FACTORY RECALL
BACK TO MENU
EXIT MENU

Содержание Rosemount 2051





































































































































































































































Отзывы:

Нет отзывов