Emerson DIXELL XR30T, Инструкции по установке и эксплуатации

Страница: 26 / 40

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 26/40
5.3 PARAMETER CONFIGURATION 2
Group Parameter Description Value Protected U.O.M. Range
rEG SEt Set Point 38.0 Pr1 °F LS to US
rEG LS Minimum Set point -148.0 Pr1 °F
[-100.0°C to SET]
[-148.0°F to SET]
rEG US Maximum Set point 302.0 Pr1 °F
[SET to 150.0°C]
[SET to 302.0°F]
rEG HY
Compressor regulation differential in
normal mode
6.0 Pr1 °F
[0.1°C to 25.0°C]
[0.1°F to 45.0°F]
rEG HYE
Compressor regulation differential in
energy saving mode
6.0 Pr1 °F
[0.1°C to 25.0°C]
[0.1°F to 45.0°F]
rEG odS Output activation delay at start-up 0 Pr1 min 0 to 255 min
rEG AC Anti-short cycle delay 0 Pr1 min 0 to 50 min
rEG rtr
Regulation percentage=F(P1; P2)
(100=P1; 0=P2)
100 Pr2 0 to 100
rEG CCt Maximum duration for Pull Down 00:00 Pr2 hh:mm 0 to 23h50min
rEG CCS
Pull Down phase differential (SET+CCS or
SET+HES+CCS)
0.0 Pr2 °F
[-12.0°C to 12.0°C]
[-21.6°F to 21.6°F]
rEG oHt
Threshold for automatic activation of Pull
Down in normal mode (SET+HY+oHt)
20.0 Pr2 °F
[0.0°C to 25.0°C]
[0.0°F to 45.0°F]
rEG oHE
Threshold for automatic activation of Pull
Down in energy saving mode
(SET+HES+HYE+oHE)
20.0 Pr2 °F
[0.0°C to 25.0°C]
[0.0°F to 45.0°F]
rEG Con Compressor ON time with faulty probe 10 Pr1 min 0 to 255 min
rEG CoF Compressor OFF time with faulty probe 15 Pr1 min 0 to 255 min
Prb P1C Probe P1 selection ntC Pr2 ntC; PtC; Pt1
Prb P2C Probe P2 selection ntC Pr2 ntC; PtC; Pt1
Prb P3C Probe P3 selection ntC Pr2 ntC; PtC; Pt1
Prb P4C Probe P4 selection ntC Pr2 ntC; PtC; Pt1
Prb ot Probe P1 calibration 0 Pr1 °F
[-12.0°C to 12.0°C]
[-21.6°F to 21.6°F]
Prb P2P Probe P2 presence Y Pr1 n(0); Y(1)
Prb oE Probe P2 calibration 0 Pr1 °F
[-12.0°C to 12.0°C]
[-21.6°F to 21.6°F]
Prb P3P Probe P3 presence no Pr1 n(0); Y(1)
Prb o3 Probe P3 calibration 0 Pr1 °F
[-12.0°C to 12.0°C]
[-21.6°F to 21.6°F]
Prb P4P Probe P4 presence no Pr1 n(0); Y(1)
Prb o4 Probe P4 calibration 0 Pr1 °F
[-12.0°C to 12.0°C]
[-21.6°F to 21.6°F]
diS CF
Temperature measurement unit: Celsius;
Fahrenheit
°F Pr1 °C(0); °F(1)
diS rES Temperature resolution: decimal, integer dE Pr1 dE(0); in(1)
diS Lod Probe default displayed P1 Pr1
P1(0); P2(1); P3(2);
P4(3); SEt(4); dtr(5)
diS dLy
Temperature display delay (resolution 10
sec)
00:00 Pr1 mm:ss 0.0 to 20min00sec
diS dtr
Probe visualization percentage=F(P1;P2)
(dtr=1 means VALUE=0.01*P1+0.99*P2)
99 Pr1 1 to 99
dEF EdF Defrost mode rtC Pr2 rtC(0); in(1)
dEF tdF Defrost type: electric heating, hot gas EL Pr2 EL(0); in(1)
dEF dFP Probe selection for defrost control P2 Pr2 nP(0); P1(1); P2(2); P3(3); P4(4)
dEF dtE End defrost temperature 48.0 Pr2 °F
[-50.0°C to 50.0°C]
[-58.0°F to 122.0°F]
dEF idF
Interval between two successive defrost
cycles
24 Pr2 ora 0 to 255 hours