Emerson Dixell IEV22D Скачать руководство пользователя страница 46

Страница: 46 / 60

1592026260 IEV22-24D GB r.1.0 21.02.2019 IEV 46/60

Et 23

Holding time of Et1 steps at the start-up of the

regulation in chiller mode

250

Sec

Et 24

Interval of updating valve position in chiller

mode

120

Sec

Et 25

Interval time for valve opening when a probe is

damaged in chiller mode

250

Sec

Et 26

Valve opening percentage when a probe is

damaged in chiller mode

100

PID configuration in heat pump mode (valve 1 and valve 2)

Et 27

PID proportional constant in heat pump mode

0.0

50.0

122

°C

°F

dec
Int

Et 28

PID integral time in heat pump mode

250

Sec

Et 29

PID derivative constant in heat pump mode

250

Sec

Et 30

Overheating regulation set point during heat

pump mode

0.0

25.0

°C

°F

dec

Int

Et 31

Overheating regulation dead band in heat

pump mode

0.0

5.0

°C

°F

dec

Int

Et 32

High overheating threshold in heat pump

mode.
The alarm status is signaled after the high
overheating alarm activation delay

Et33

80.0

176

°C

°F

dec

Int

Et 33

Low overheating threshold in heat pump mode.

The alarm status is signaled after the low
overheating alarm activation delay

0.0

Et32

°C

°F

dec

Int

Et 34

Low overheating protection added integral time

in heat pump mode

250

Sec

Et 35

MOP Protection activation threshold in heat

pump mode.
High evaporating temperature threshold. The
alarm status is signaled after the high
evaporating temperature alarm activation delay

-70.0
-94

60.0
140

°C

°F

dec

Int

Et 36

Step Rate during MOP or LOP protection

(number of steps every second) in heat pump
mode

8000 Full steps

Et 37

LOP Protection activation threshold in heat

pump mode.
Low evaporating temperature threshold. The
alarm status is signaled after the low
evaporating temperature alarm activation delay

-70.0
-94

60.0
140

°C

°F

dec

Int

Et 38

Percentage decreasing in case of low

superheating condition in heat pump mode

100

Et 39

Max. value of valve opening in heat pump

mode (percentage)

Et40 100

Et 40

Min. value of valve opening in heat pump mode

(percentage)

Et39

Et 41

Pressure measure Filter in heat pump mode

250

Sec

Et 42

Temperature measure filter in heat pump mode

250

Sec

Содержание Dixell IEV22D





























































Результаты поиска

Содержание Dixell IEV22D

Отзывы:

Emerson Dixell IEV22D, Руководство пользователя, Страница: 46 / 60

Результаты поиска

Содержание Dixell IEV22D

Отзывы: