Emerson Dixell IEV22D Скачать руководство пользователя страница 45

Страница: 45 / 60

1592026260 IEV22-24D GB r.1.0 21.02.2019 IEV 45/60

Et 6

Absolute number of steps the valve has to

move in manual mode

Ec23 Ec22 Full steps

PID configuration in chiller mode (valve 1 and valve 2)

Et 7

PID proportional constant in chiller mode

0.0

50.0

122

°C

°F

Dec

Int

Et 8

PID integral time in chiller mode

250

Sec

Et 9

PID derivative constant in chiller mode

250

Sec

Et 10

Overheating regulation set point during chiller

mode

0.0

25.0

°C

°F

dec

Int

Et 11

Overheating regulation dead band in chiller

mode

0.0

5.0

°C

°F

dec

Int

Et 12

High overheating threshold in chiller mode.

The alarm status is signaled after the high
overheating alarm activation delay

Et46

80.0

176

°C

°F

dec

Int

Et 13

Low overheating threshold in chiller mode.

The alarm status is signaled after the low
overheating alarm activation delay

0.0

Et46

°C

°F

dec

Int

Et 14

Low overheating protection added integral time
in chiller mode

250

Sec

Et 15

MOP Protection activation threshold in chiller

mode.
High evaporating temperature threshold. The
alarm status is signaled after the high
evaporating temperature alarm activation delay

-70.0
-94

60.0
140

°C

°F

dec

Int

Et 16

STEP RATE during MOP or LOP protection

(number of steps every second) in chiller mode

8000 Full steps

Et 17

LOP Protection activation threshold in chiller

mode.
Low evaporating temperature threshold. The
alarm status is signaled after the low
evaporating temperature alarm activation delay

-70.0

-94

60.0

140

°C

°F

dec

Int

Et 18

Percentage decreasing in case of low

superheating condition in chiller mode

100

Et 19

Maximum value of valve opening in chiller

mode (percentage)

Et20 100

Et 20

Minimum value of valve opening in chiller

mode (percentage)

Et19

Et 21

Pressure measure filter in chiller mode

250

Sec

Et 22

Temperature measure filter in chiller mode

250

Sec

Содержание Dixell IEV22D





























































Результаты поиска

Содержание Dixell IEV22D

Отзывы:

Emerson Dixell IEV22D, Руководство пользователя, Страница: 45 / 60

Результаты поиска

Содержание Dixell IEV22D

Отзывы: