Emerson Damcos KC 125 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 46

Emerson Damcos KC 125 Скачать руководство пользователя страница 5

General Information

Quick Installation Guide

February 2020

QIG 8000-81-003 Ed 01

3

General Information

Introduction

This instruction covers dismounting, disassembling and installation of the Actuator KC 65, KC 125,
KC 250, KC 325, KC 400 when mounted to a valve with extended stem/bonnet.

Reservations

•

Installation or repair must be performed by trained personnel only.

•

Tools and equipment used for installation and repair must in good condition and calibrations up
to date.

•

Illustrations shown in this instruction reflect actuators with control block and electrical DPI.
However, the instruction will be applicable for actuators without DPI too. Pay attention to notes
for models ‘with’ or ‘without’ DPI.

•

The environment must be clean and without the risk of getting dirt into the unit when taken
apart. Make sure you have access to an indoor workshop for the actual repair.

•

Any damage caused by incorrect handling of the equipment is not covered by the manufac-
turer’s warranty.

Warning, Cautions and Notes

In order to avoid any personal injuries, damage of equipment or loss of production time, please
observe and obey Warning, Cautions, and Notes made throughout this document.
The following warning levels are used in the documentation of Damcos A/S for the safety of people
and equipment.

Warning!

Indicates a potentially hazardous situation which, if not avoided, could result in death or
serious injury.

Caution!

Indicates a potentially hazardous situation which, if not avoided, may result in property
damage.

Note!

Indicates important information regarding the product.

«
...
3
4
5
6
7
...
»

Содержание Damcos KC 125















































Отзывы:

Нет отзывов