Emerson Damcos KC 125 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 46

Emerson Damcos KC 125 Скачать руководство пользователя страница 31

Preparations before Dismounting

Quick Installation Guide

February 2020

QIG 8000-81-003 Ed 01

29

Dismounting and Disassembling

Preparations before Dismounting

Caution!

If the actuator is about to be dismounted for repair, on board a ship the description of
dismounting from the valve bonnet must be followed.

Warning!

If not done already, advise the system operators and other relevant persons that main-
tenance is ongoing.
Make sure that relevant operation systems are set to maintenance mode, and alterna-
tive means of operation is ensured (if required).

Warning!

IKeep clear of moving valve parts due to risk of personal injury!

Empty from Oil

Before disassembling, the actuator has to be emptied from the oil. Please refer to system procedures
and documentation. Ref. documents listed on page 2 in this instruction.

Open the Valve and Actuator

The valve must be in state ‘open’ before the
actuator can be dismounted from the valve bon-
net/stem.

Ensure that the indicator disc (a) on the stem
shaft is positioned next to the marking for
‘Open’ (b) on the bonnet and/or the visual indi-
cator (c) on the actuator shows ‘Open’.

«
...
29
30
31
32
33
...
»

Содержание Damcos KC 125















































Отзывы:

Нет отзывов