manualshive.com logo in svg

Emerson Damcos KC 125, Быстрое руководство по установке, Страница: 27 / 46

Поделиться
Скачать
Emerson Damcos KC 125 Скачать руководство пользователя страница 27

Trouble Shooting

Quick Installation Guide

February 2020

QIG 8000-81-003 Ed 01

25

Trouble Shooting

If fault:

Possible cause

Remedy

Actuator (valve) is not 
operating!

No oil pressure

Check the oil pressure at supply unit (it 
should be 135 bar).

The cross-over valve on the 
actuator is not fully closed.

Make sure the cross-over valve is fully 
closed.

Some models only!

The throttle on the control 
block is set to minimum flow. 

Open the throttle on the control block.

No open signal from actuator

Stroke is reduced by incorrect 
mounting

Ensure that stroke is according to valve 
requirements.
See also ‘Determine the Configured 
Stroke’ on page 23 in this instruction.

Faulty adjustment of indicator

Adjust the indicator.
See DPI data sheet SD 2000-0E07 page 2.

No closed signal from actuator

Stroke is reduced by incorrect 
mounting

Ensure that stroke is according to valve 
requirements.
See also ‘Determine the Configured 
Stroke’ on page 23 in this instruction.

Incorrect adjustment of the 
indicator

Adjust the indicator
See DPI data sheet SD 2000-0E07 page 2.

The actuator stroke does not 
match the valve stroke

Check actuator stroke mark in the 
bottom of the actuator (ref. ‘Determine 
the Configured Stroke’ on page 23 in this 
instruction).

Wrong indicator bushing

Check indicator bushing without 
dismantle. See ‘Determine the 
Configured Stroke’ on page 23 in this 
instruction.

Request correct size of indicator bushing. 

Replace the indicator bushing (ref. 
‘Assembling the Actuator’ in this 
instruction). Note! This may compromise 
warranty.

Wrong yoke

Consult specific PSM list and get correct 
yoke

Содержание Damcos KC 125















































Отзывы:

Нет отзывов