Emerson Damcos KC 125 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 46

Emerson Damcos KC 125 Скачать руководство пользователя страница 17

Test of DPI-E, On/Off signals

Quick Installation Guide

February 2020

IG 8000-81-003 Ed 01

15

Test of the DPI

DPI models only

Some actuators are equipped with a DPI (Direct Position Indicator). The DPI on KC Actuators will be
either DPI-E or DPI-C.
The tests described in the following can be made on the actuator when mounted on the valve bon-
net/stem as well as when dismounted.

Test of DPI-E, On/Off signals

Test of DPI-E, On/Off signals

1.

Connect a hydraulic hand
pump (if not connected
already) by dismounting
the caps (d) from the two
hydraulic connection fit-
tings and connect the
pump hoses to fittings A
and B.

2.

Make sure the visual indi-
cator (c) shows closed.

3.

Operate the hand pump
and observe that the spin-
dle (e) moves in (1 = actu-
ator is open) and out (2 =
actuator is closed).

4.

Ensure that the actuator
is in position 2 = closed
(the spindle is in max.
‘out’ position) before con-
tinuing with step 5.

«
...
15
16
17
18
19
...
»

Содержание Damcos KC 125















































Отзывы:

Нет отзывов