5
1. Cut the white, blue, and black wires about 3"
above the motor coupling (Figure 1A). Strip
insulation 1/2" from end of wires and install a wire
connector on the black wire; this wire will not be
used. Remove the wire connectors from the red
and brown wires.
2. Remove the wire connector that is connecting the
two yellow leads (Figure 1A). Disconnect the two
yellow leads and reinstall a wire connector to the
yellow lead from the motor only; this lead will not
be used.
3. Loosen the setscrew in the hanger ball, slide the ball
down the downrod, and remove the clevis pin. Then
slide the hanger ball off the downrod (Figure 2A).
Retain all parts for reinstallation in Step 12.
4. Push the wiring harness connector and the
connector on the blue wire (both supplied with the
SR330 Remote Control and the SW350 Wall
Control), and the connector on the uplight yellow
lead assembly (supplied with the fan) through the
downrod until they all extend about 4” out of the
downrod (Figure 3A).
5. Cut all wires approximately 3" from the end of the
downrod. Strip insulation 1/2" from end of wires.
3"
WHITE WIRE
BLACK WIRE
BLUE WIRE
REMOVE WIRE
CONNECTORS
FROM RED AND
BROWN WIRES
INSULATE BLACK
WIRE USING WIRE
CONNECTOR
YELLOW
WIRE FROM
MOTOR
MOTOR
COUPLING
MOTOR COUPLING SLOT
WIRE
CONNECTOR
(Connected to
Yellow Lead
from Motor Only)
YELLOW LEAD
(Disconnected
from wire connector)
Figure 1A
HANGER BALL
DOWNROD
CLEVIS PIN
SETSCREW
Figure 2A
4"
DOWNROD
CUT HERE
3"
UPLIGHT YELLOW LEAD ASSEMBLY
WIRING
HARNESS
BLUE WIRE
Figure 3A
6. Using wiring connectors (supplied), connect the
white, red, blue, brown, and yellow wires from the
downrod to the white, red, blue, brown and yellow
wires of the ceiling fan (Figure 4A). Wires must be
connected color-to-color.
7. Fold all wires from the downrod into the slot in the
motor coupling, slide the downrod down the wires
and seat the downrod in the motor coupling. All
wires and wire connectors should be placed
through the motor coupling slot beneath the
downrod (See Figure 5A).
8. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip. The clevis pin
must go through the holes in the motor coupling
and the holes in the downrod (Figure 5A). Push
the straight leg of the hairpin clip through the hole
near the end of the clevis pin until the curved
portion of the hairpin clip snaps around the clevis
pin. The hairpin clip must be properly installed to
prevent the clevis pin from working loose.
FAN BLADES REMOVED
FOR CLARITY
TM
DOWNROD
BLACK WIRE
WHITE WIRE
WIRING HARNESS
CONNECTOR
YELLOW WIRE
TO YELLOW
WIRE
BLUE WIRE
TO
BLUE WIRE
RECEIVER
BROWN WIRE
TO BROWN WIRE
YELLOW WIRE
TO YELLOW WIRE
FROM UPLIGHT
LISTED GENERAL
USE ON/OFF
WALL SWITCH
(MUST BE
USED WITH SR120
REMOTE CONTROL)
RECEIVER
CONNECTOR
RED WIRE
TO RED WIRE
WHITE WIRE
TO WHITE WIRE
BLACK WIRE
(NOT USED)
BLUE WIRE
TO BLUE WIRE
BLACK WIRE
WHITE WIRE
BLACK
WIRE
WHITE
WIRE
BLACK
WHITE
BLACK
SW140
WALL
CONTROL
FAN
HOUSING
TO
120V SUPPLY
TO
120V SUPPLY
YELLOW WIRE
FROM MOTOR
COUPLER
(NOT USED)
LIGHT FIXTURE
Figure 4A
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely
tightened. Failure to verify that the pin and setscrew
are properly installed could result in the fan falling.
WARNING
!
SECTION A
Assembly Instructions for Installing the CF4800 or CF4500 Ceiling Fan
with the Emerson SR330 Remote Control or the SW350 Wall Control
