c. Securely connect the blue wire from the
downrod to the supply red (hot) wire using wire
connector (supplied). After connections have
been made, turn leads upward and carefully
push leads into the outlet box, with the white
and green leads on one side of the outlet box
and the black, blue and yellow leads on the
other side of the outlet box.
17. Screw the two 1-1/4” threaded studs (provided)
into the tapped holes in the hanger bracket.
18. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 12B).
19. Secure the ceiling cover in place by sliding
lockwashers over the threaded studs and
installing the two knurled knobs (supplied).
(Figure 12B.) Tighten the knurled knobs securely
until the ceiling cover fits snugly against the
ceiling and the hole in the ceiling cover is clear of
the pipe.
20. Screw in three 40-watt (maximum) candelabra
base lamps into the uplight sockets on top of the
fan housing assembly.
21. Connect the pendant and chain (supplied) to the
switch pull chain using the coupling (supplied).
11
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
WARNING
!
BLACK
BLACK FAN WIRE
LISTED OUTLET BOX
LIGHT
CONTROL
GREEN WIRE
(GROUND)
FROM
HANGER
BRACKET
TO 120
VOLT
SUPPLY
WHITE
GROUND
GROUND
GREEN WIRE (GROUND)
FROM HANGER BALL
LISTED WIRE CONNECTOR (4)
GROUND
WIRE
WHT.
EMERSON FAN CONTROL
BLACK
(HOT)
BLUE
RED
THREE - CONDUCTOR CABLE
WITH GROUND BETWEEN
CEILING AND WALL OUTLET
BOXES
Figure 11B
1-1/4"
THREADED
STUD
LOCKWASHERS (2)
CEILING COVER
KNURLED KNOB
Figure 12B
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
WARNING
!
Using Your Ceiling Fan
1. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box.
2. When controlled by a wall switch check the
operation of the fan by gently pulling on the 4-
position speed control pull chain switch. (This
switch has the longer pull chain.) The operating
sequence is as follows:
THREE-SPEED
1st Pull—HIGH
2nd Pull—Medium
3rd Pull—Low
4th Pull—OFF
3.When operated by an Emerson Remote Control,
check operation of fan and light in accordance with
the Remote Control Owner’s Manual.
4. If airflow is desired in opposite direction, turn your
fan off and wait for the blades to stop turning. Then
slide the reversing switch to the opposite position
and turn fan on again. The fan blades will turn in
the opposite direction and reverse the airflow.
Attaching Light Kit
To install an Emerson accessory light kit, remove the
three screws securing the switch cup assembly to the
fan, remove the switch cup assembly, and disconnect
the connector. Remove the screw plug from the
bottom of the switch cup and install the light kit in
accordance with the Emerson light kit Owner's
Manual.
SPEED
CONTROL
SWITCH
REVERSIBLE
SWITCH
TM
To avoid possible electrical shock, be sure electricity
is turned off at the main service box before wiring.
WARNING
!
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
WARNING
!
