manualshive.com logo in svg

Emerson Control Techniques Epsilon Eb-202, Руководство по установке

Поделиться
Скачать
Emerson Control Techniques Epsilon Eb-202 Скачать руководство пользователя страница 73

58

Epsilon Eb Digital Servo Drive Installation Manual

2. If the combination of command pulse frequency and Pulse 

Ratio can generate a motor command speed in excess of the 

fixed limit of 13000 RPM, an Overspeed Fault will be 

activated. In Pulse mode operation and any Summation 

mode which uses Pulse mode, the input pulse command 

frequency is monitored and this calculation is made. For 

example, with a Pulse Ratio of 10 pulses per motor 

revolution, the first pulse received will cause an Overspeed 

fault even before there is any motor motion.

Max Following Error

This fault is generated when the following error exceeds the 

following error limit (default following error limit is .2 revs). 

With PowerTools you can change the Following Error Limit 

value or disable in the Position tab.

Travel Limit +/- 

This fault is caused when either the + or - Travel Limit input 

function is active.

"All On"

This is a normal condition during power up of the drive. It will 

last for less than 1 second. If this display persists, call 

EMERSON for service advice.
Normally, "All On" appears for less than one second during 

power-up. All segments are dimly lit when power is "Off." This 

is normal when an external signal is applied to the encoder 

inputs (motor or master) or serial port from an externally 

powered device. The signals applied to the inputs cannot 

exceed 5.5V level required to drive logic common or drive 

damage will occur.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Control Techniques Epsilon Eb-202







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды