Emerson Control Techniques Epsilon Eb-202 Скачать руководство пользователя страница 43

Страница: 43 / 134

Epsilon Eb Digital Servo Drive Installation Manual

Figure 12:

Epsilon Auxiliary Power Supply Wiring Diagram

Alternate Power Supply Wiring

An Alternate Power Supply (APS) allows the drive to retain

motor position information and serial communications when

the main AC power supply is disconnected. You must reset the

drive, either using the reset button or a reset input, after AC

power is re-applied if the backup supplies have been active.
Enabling APS power is done by sliding open the access panel on

the side of the drive. Then move the jumper into the APS

position using needle nose pliers.

Side View

Front View

24 VDC

Important:

Slide the side access panel

up into the open position. Remove the
jumper from the AC position (Default)
and reinstall it into the 24 V position
(A.P.S.). The instruction on the side of
the drive will show which position to put
the jumper.

2 A

Fuse

Single point PE

ground

(recommended)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Control Techniques Epsilon Eb-202







































































































































Результаты поиска

Содержание Control Techniques Epsilon Eb-202

Отзывы:

Бренды по названию

Популярные бренды

Emerson Control Techniques Epsilon Eb-202, Руководство по установке

Результаты поиска

Содержание Control Techniques Epsilon Eb-202

Отзывы:

Бренды по названию

Популярные бренды