manualshive.com logo in svg

Emerson Control Techniques Epsilon Eb-202, Руководство по установке

Поделиться
Скачать
Emerson Control Techniques Epsilon Eb-202 Скачать руководство пользователя страница 44

29

Installation

Use static control procedures when handling the jumper inside 

the drive case. 
The APS input is isolated from all other circuits on the Epsilon 

drive including the DC bus, logic and I/O. This permits you to 

use one common 24 VDC power supply for multiple drives 

without concern for ground loops and noise coupling between 

drives. The APS connection will generate some high frequency 

ripple (.25 Amps at 80 khz) on the APS power lines. This may 

disturb sensitive equipment that shares the same power 

supply.

APS Input Specification

Using the APS supply input to power the drive logic and motor 

encoder allows the drive bus to operate at DC voltages below 42 

VAC (60 VDC bus). The drive will operate down to 12 VDC on 

the bus (10 VAC on L1 and L2). However the low DC bus 

monitoring must be disabled to prevent faults at these low DC 

bus voltage levels. This can be done with PowerTools software 

on the Advanced tab in Detailed Setup mode.

Caution

Do not wire AC line into the APS input. Doing so will 

damage the drive.

Voltage Range

Current

Inrush Current

18-30 VDC

0.5 A maximum

0.7 A peak

( 0.4 A maximum

0.6 A peak if external 

encoder is not used )

80 A for 1 ms if not limited by 

power supply

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Control Techniques Epsilon Eb-202







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды