Emerson Control Techniques Epsilon Eb-202 Скачать руководство пользователя страница 63

Страница: 63 / 134

Epsilon Eb Digital Servo Drive Installation Manual

Caution

When connecting the serial port of your PC to the serial port

of the drive, verify that your PC’s ground is the same as the

drive PE ground. Failure to do so can result in damage to

your PC and/or your drive.

Note

Communication errors can usually be avoided by powering

the computer or host device off of a convenience outlet that

is mounted in the enclosure and whose neutral and ground

are wired to the same single ended point ground that the

drives and controllers are using.

This is sometimes benefical even with battery powered

computers.

Modbus Communications

The drive’s serial communication protocol is Modbus RTU

slave with a 32 bit data extension. The Modbus protocol is

available on most operator interface panels and PLC’s.

EMERSON Motion Control’s Motion Interface panels are

supplied with a Modbus master communications driver.

Serial Communications Specifications

Max baud rate

19.2k

Start bit

Stop bit

Parity

none

Data

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Control Techniques Epsilon Eb-202







































































































































Результаты поиска

Содержание Control Techniques Epsilon Eb-202

Отзывы:

Бренды по названию

Популярные бренды

Emerson Control Techniques Epsilon Eb-202, Руководство по установке

Результаты поиска

Содержание Control Techniques Epsilon Eb-202

Отзывы:

Бренды по названию

Популярные бренды