Emerson Control Techniques Epsilon Eb-202 Скачать руководство пользователя страница 33

Страница: 33 / 134

Epsilon Eb Digital Servo Drive Installation Manual

Note

For Epsilon drives, surrounding air ambient temperature

can be up to 50°C (122° F) with 3% linear derating for every

degree above 40° C (104° F)

The amount of cooling depends on the size of the enclosure, the

thermal transfer of the enclosure to the ambient air and the

amount of power being dissipated inside the enclosure. Consult

your enclosure manufacturer for assistance with determining

cooling requirements.

Wiring Notes

• To avoid problems associated with EMI (electromagnetic

interference), you should route high power lines (AC input power and
motor power) away from low power lines (encoder feedback, serial

communications, etc.).

• If a neutral wire (not the same as Earth Ground), is supplied from the

building distribution panel it should never be bonded with PE wire in

the enclosure.

• You should consider future troubleshooting and repair when

installing all wiring. All wiring should be either color coded and/or

tagged with industrial wire tabs.

• As a general rule, the minimum cable bend radius is ten times the

cable outer diameter.

• All wiring and cables, stationary and moving, must be protected from

abrasion.

• Ground wires should not be shared with other equipment.

• Ensure that metal to metal contact is made between the enclosure

ground lug and the metal enclosure, not simply through the mounting
bolt and threads.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Control Techniques Epsilon Eb-202







































































































































Результаты поиска

Содержание Control Techniques Epsilon Eb-202

Отзывы:

Бренды по названию

Популярные бренды

Emerson Control Techniques Epsilon Eb-202, Руководство по установке

Результаты поиска

Содержание Control Techniques Epsilon Eb-202

Отзывы:

Бренды по названию

Популярные бренды