Emerson Control Techniques Epsilon Eb-202 Скачать руководство пользователя страница 54

Страница: 54 / 134

Installation

For information about Command Connector pinout and

CMDO-XXX cable wire colors, see the "Specifications" section.

Command Cables

The CMDO, CMDX and CDRO cables are all cables that plug

into the Command Connector.
The CMDO and CMDX cables both use the same straight

connector style, same color code and carry the full complement

of signals available from the Command Connector. The

difference is the CMDO cable has a male connector on one end

Function

Pin Numbers

Electrical Characteristics

Inputs and Drive

Enable

1, 2, 3, 4, 16

10-30 V (“On”) 0-3 V (“Off”) optically isolated

Outputs

17, 18, 19

10-30 VDC sourcing 150 mA

I/O Supply

33, 34

10 - 30 VDC @ 1 Amp maximum

I/O Common

31, 32

I/O return

Pulse Inputs

Differential

25, 26, 27, 39, 40,

5 V, 200 mV differential, 60 mV hysteresis, RS-422

compatible

Pulse Inputs Single

Ended

20, 36

TTL, 330 ohm pull-ups to internal 5 V, 1.5 V = low,

3.5 V = high

Encoder Supply Output

+5 V

+5 V (200mA) output self-resetting fused internally

Encoder Common 0 V

0.0 V, 10 ohms away from PE

Encoder Out

8, 9, 23, 24, 37, 38 Differential line driver output (RS 422)

Analog In

14, 15

± 10 VDC differential command

Diagnostic Output

43, 44

± 10 VDC 10 mA maximum. Analog diagnostic

output, ref. to pin 29

Diagnostic Output

Common

0.0 V, 10 ohms away from PE

0 ohms away from Encoder Common 0V (pin 12)

RS 485 ±

6, 21

Same signals as the Serial Connector

+15 out

10 mA supply. ref. pin 29 (for test purposes only.)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Control Techniques Epsilon Eb-202







































































































































Результаты поиска

Содержание Control Techniques Epsilon Eb-202

Отзывы:

Бренды по названию

Популярные бренды

Emerson Control Techniques Epsilon Eb-202, Руководство по установке

Результаты поиска

Содержание Control Techniques Epsilon Eb-202

Отзывы:

Бренды по названию

Популярные бренды