Emerson ACC/ARTM-7221/FC Скачать руководство пользователя страница 50

Страница: 50 / 54

ACC/ARTM-7221/FC Installation Guide (6806800E98A

)

Installation

Devices Connected to RTM's Mezzanine Management Controller

The location of the temperature sensor ARTM7221 Temp. is shown in the following figure.

For further details about IPMI sensors as well as supported IPMI commands, refer to the

ACC/ARTM-7221/FC: Control via IPMI Programmer's Guide

which can be downloaded from

the Emerson literature catalog.

V5V USB1

Voltage

+5V voltage level of USB interface
1

Analog

While Payload
powered ON

V5V USB2

Voltage

+5V voltage level of USB interface
2

Analog

While Payload
powered ON

Volt +5V KB PWR

Voltage

+5V voltage level of
keyboard/mouse interface

Analog

While Payload
powered ON

ARTM FW Revision

Firmware revision

Application firmware revision

Discrete

Always

ARTM-7221 MMC

Reset type

Status and type of the last reset of
the IPMC

Discrete

Always

BOOT FW Revision

Firmware revision

Boot loader firmware revision

Discrete

Always

Table 2-3 Available IPMI Sensors (continued)

Sensor Name

Type of
Measurement

What does it measure?

Sensor
Type

Sensor
Availability

Figure 2-23 Location of IPMI Temperature Sensor

Location of IPMI sensor
ARTM-7221 Temp.

Содержание ACC/ARTM-7221/FC























































Результаты поиска

Содержание ACC/ARTM-7221/FC

Отзывы:

Бренды по названию

Популярные бренды

Emerson ACC/ARTM-7221/FC, Руководство по установке

Результаты поиска

Содержание ACC/ARTM-7221/FC

Отзывы:

Бренды по названию

Популярные бренды