manualshive.com logo in svg

Emerson ACC/ARTM-7221/FC, Руководство по установке

Поделиться
Скачать
Emerson ACC/ARTM-7221/FC Скачать руководство пользователя страница 38

ACC/ARTM-7221/FC Installation Guide (6806800E98A

)

Installation

Powered System

38

   

5.

Insert the RTM into the shelf by placing the top and bottom edges in the card guides 
of the slot

6.

Slide the RTM into the slot

7.

Hook the lower and the upper handle into the shelf rail recesses

8.

Fully insert the RTM and lock it to the shelf by pressing the two components of the 
lower and upper handles together and turning the handles towards the face plate

9.

Close the lower handle of the front blade
The front blade and the RTM are powered up while the blue LED on the front blade 
is flashing.

10.

Tighten both face plate screws on the RTM

11.

Wait until the blue LED of the front blade is OFF

12.

Plug interface cables into face plate connectors, if applicable

Installation Procedure without Installed Front Blade

1.

Ensure that the top and bottom handles of the RTM are in outward position

2.

Insert the RTM into the shelf by placing the top and bottom edges in the card guides 
of the slot

3.

Slide the RTM into the slot

4.

Hook the lower and the upper handle into the shelf rail recesses

5.

Fully insert the RTM and lock it to the shelf by pressing the two componentes of the 
lower and upper handles and turning the handles towards the face plate

6.

Fasten both screws on the RTM

7.

Insert the front blade from the system's front into the same slot as the RTM

8.

Close the handles of the front blade
The blue LED on the front blade starts flashing during the power-up procedure.

9.

Tighten the two face plate screws on the front blade

RTM Malfunctioning
Incorrect RTM installation and removal can result in RTM malfunctioning.
When plugging the RTM in or removing it, do not press on the face plate but use the 
handles.

Содержание ACC/ARTM-7221/FC























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды