manualshive.com logo in svg

Emerson ACC/ARTM-7221/FC, Руководство по установке

Поделиться
Скачать
Emerson ACC/ARTM-7221/FC Скачать руководство пользователя страница 37

Powered System

Installation

ACC/ARTM-7221/FC Installation Guide (6806800E98A)

37

   

Removal Procedure

1.

Remove interface cables from the face plate connectors, if applicable

2.

Loosen the two face plate screws

3.

Open the lower and upper handle by pressing the two handle components together 
and turning the handles outwards.

4.

Remove the RTM from the slot

5.

Turn on the system power

2.4.2

Powered System

You can install the RTM into a powered system if the front blade is already installed or if it is not 
already installed. If the front blade is already installed, its payload has to be powered down first.  

Installation Procedure with Installed Front Blade

1.

Locate the slot the RTM is to be installed into at the shelf's  rear which must be the 
same as that of the front blade

2.

Open the lower handle of the front blade
The blue LED on the front blade starts to flash while the front blade powers down.

3.

Wait until the blue LED on the front blade is ON

4.

Ensure that the top and the bottom handles of the RTM are in outward position

RTM Malfunctioning
Incorrect RTM installation and removal can result in RTM malfunctioning.
When plugging the RTM in or removing it, do not press on the face plate but use the 
handles.

Damage of Circuits
Electrostatic discharge and incorrect RTM installation and removal can damage 
circuits or shorten their life.
Before touching the RTM or electronic components, make sure that you are working 
in an ESD-safe environment.

Содержание ACC/ARTM-7221/FC























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды