manualshive.com logo in svg

Emerson ACC/ARTM-7221/FC, Руководство по установке

Поделиться
Скачать
Emerson ACC/ARTM-7221/FC Скачать руководство пользователя страница 45

LEDs

Installation

ACC/ARTM-7221/FC Installation Guide (6806800E98A)

45

   

A detailed description of each LED is given in the following table. 

The status of all LEDs can be determined via the PICMG 3.0 command "Get FRU LED State". 
The status of the LEDs can be changed via the PICMG 3.0 command "Set FRU LED State".

Table 2-2 LED Description

LED

Description

OOS

Out-of-Service

This LED is controlled by upper layer software, such as middleware or 
applications. It works in parallel to the OOS LED at the front blade's face plate. 

OK

RTM Power Status

Green: The RTM power has been enabled by the MMC. 

OFF: RTM power is disabled

ACT

This LED is controlled by upper layer software, such as middleware or 
applications. It works in parallel to the ACT LED at the front blade's face plate. 

H/S

Indicates whether the RTM can be installed or removed

During RTM installation

:

Permanently blue: RTM powers up

Flashing blue: RTM communicates with shelf management controller

OFF: RTM is active

During RTM removal

:

Flashing blue: RTM notifies shelf management controller of desired 
deactivation. In this state the RTM must not be removed.

Permanently blue: RTM is powered down and is ready to be extracted

OFF: RTM is active and cannot be removed

Содержание ACC/ARTM-7221/FC























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды