Emerson 1F83-0422, Инструкция по эксплуатации

Страница: 5 / 12

5
INSTALLER/CONFIGURATION MENU
1)
Keypad Lockout
– This menu selection will display “
Lk”
and “OFF” (default, keypad not locked out). The and
are used to toggle the selection between OFF and
“
L”
(keypad locked out). When the keypad lockout selec-
tion is enabled “L” , and the MENU button is pressed
again, the display will indicate the number “0” (default,
still disabled) in the time digits. The and are
used to set the combination number from
0
to
999
. If a
combination of 0 is selected and the MENU button is
pressed, the menu will be exited and keypad will not be
locked. If
1
to
999
is selected and the MENU button is
pressed, the combination is stored into memory and the
menu is exited. The “ LOC” will display designating key-
pad locked with a valid combination. The SYSTEM button
will operate for 10 seconds after the menu mode is exited
to allow the user to change the mode from “ OFF” to the
desired SYSTEM mode.
While the keypad is locked out, a press of MENU will en-
ter the configuration menu. The first menu item displayed
is the combination code “ 0” . The or keys are
used to set the combination unlock number from
0
to
999
. If the unlock number matches exactly with the com-
bination lock number stored in memory when the MENU
button is pressed, the keypad is unlocked and the “LOC”
is removed. If the unlock number does not match when
the MENU button is pressed, the combination returns to
“0” for another attempt to set the unlock code. To exit the
menu without unlocking the keypad, press RUN SCHED.
To reset the combination code and unlock the keypad if
the code is forgotten, see troubleshooting section.
2) This control can be configured for:
MS 2 – Multi-Stage System (no heat pump)
HP 1 – Heat Pump with one stage of compressor
SS 1 – Single Stage System
3) GAS or Electric (ELE) fan operation. If the heating sys-
tem requires the thermostat to energize the fan, select
ELE. Select GAS if the heating system energizes the fan
on a call for heat.
4)
Select Cool Savings™ value
– Selects the amount
of adjustment for the Cool Savings™ feature in Cool
mode with 1 (1°) being the least amount of adjustment
and 6 (6°) being the most amount of adjustment. Default
value is 0 which disables this feature. Cool Savings is
an optional energy saving feature that can reduce your
cooling costs. It is based on the principal that lower
indoor humidity makes a slightly higher temperature
feel more comfortable. Cool Savings operates during
periods of high demand which normally occur on the
hottest summer days when a cooling system may run
for hours to reach the thermostat setting. Long cooling
run times also lower the indoor humidity. Cool Savings,
very slowly, adjusts the setpoint temperature to make the
setpoint closer to the displayed room temperature, to a
maximum of the number of degrees you select. Adjust-
ing the setpoint temperature over a long cooling run time
allows the system to reach your set temperature and turn
off. The room temperature will actually be higher than
the thermostat displays but the reduction in humidity will
allow comfort at the slightly higher temperature.
To turn this feature on in the Cool mode press Cool
Savings. The display will show “Save” next to the
setpoint temperature. When Cool Savings is making ad-
justments to the room temperature display
“Save”
will be
flashing and the displayed room temperature may vary
within the adjustment range you selected.
If
“Save”
is not displayed and this feature is OFF, no
change will occur when the cooling system is continu-
ously running during periods of high demand.
5) Energy Management Recovery: (this step is skipped if
configured to be non-programmable). Energy Manage-
ment Recovery (E) On enables the thermostat to start
heating or cooling early to make the building temperature
reach the program setpoint at the time you specify. Heat-
ing will start 5 minutes early for every 1° of temperature
required to reach setpoint.
Example: E On is selected and your heating is pro-
grammed to 65° at night and 70° at 7 AM. If the build-
ing temperature is 65°, the difference between 65° and
70° is 5°. Allowing 5 minutes per degree, the thermostat
setpoint will change to 70° at 6:35 AM. Cooling allows
more time per degree, because it takes longer to reach
set temperature.
6, 7 & 8) Cycle Rate Selection – The factory default setting
for Heat and Cool modes, SS1 and MS2 is medium cycle
(ME). For Heat Pump and HP1, the default setting is
medium (ME). For Emer (Aux) the default setting is fast
cycle (FA). To change cycle rate, press the or
key.
Cycle rate differentials for different settings are:
Fast Medium Slow
MODE FA ME SL
Heat (SS1, MS2) 0.4°F 0.6°F 1.7°F
Cool (SS1, MS2) 0.9°F 1.2°F 1.7°F
Heat Pump (HP1) 0.9°F 1.2°F 1.7°F
Emer (HP1) 0.6°F - 1.7°F
9)
Select Compressor Lockout CL OFF or ON
– Select-
ing CL ON will cause the thermostat to wait 5 minutes
between cooling cycles. This is intended to help protect
the compressor from short cycling. Some newer com-
pressors already have a time delay built in and do not
require this feature. Your compressor manufacturer can
tell you if the lockout feature is already present in their
system. When the thermostat compressor time delay oc-
curs, it will flash the setpoint for up to five minutes.
10) System Mode Configuration – This thermostat is con-
figured for Heat and Cool (SYSTEM switch with Cool Off
Heat) default. It can also be configured for Heat and Cool
with Auto changeover (Heat, Auto, Cool, Off), Heat only
with fan (Off Heat), Heat only without fan, Auto only
(Auto Off), and Cool only (Cool Off).
11)
Select Backlight Display
– The display backlight im-
proves display contrast in low lighting conditions. When
the “C” terminal is powered, selecting backlight CdL ON
will keep the light on continuously. Select backlight OFF
will turn the light on momentarily after any key is pressed.
When the “C” terminal is not powered, the light will be on
momentarily after any key is pressed no matter whether
the backlight is selected ON or OFF.
12) Select Temperature Display Adjustment 4 LO to 4 HI
– Allows you to adjust the room temperature display up
to 4° higher or lower. Your thermostat was accurately cali-
brated at the factory, but you have the option to change
the display temperature to match your previous thermo-
stat. The current or adjusted room temperature will be
displayed.
13) Select F° or C° Readout – Changes the display readout
to Celsius or Fahrenheit as required.
14) Limited Heat Range – This feature provides a maximum
setpoint temperature for heat. The default setting is 90
°
F.
It can be changed between 62°F and 89°F by pressing
the or key.
15) Limited Cool Range – This feature provide a minimum
setpoint temperature for cool. The default setting is 45
°
F.
It can be changed between 46 ° F and 82 ° F by pressing
the or key.
16) Program Options: 1F85 only, configured for 5/1/1 day or
5/2 day programming or non-programming mode. The
default setting is P3, indicating 5/1/1 day programming.
The programs per week can be changed to P2 or P0 by