ELTEX SMG-2 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 198

ELTEX SMG-2 Скачать руководство пользователя страница 110

110

SMG digital gateway

When data collection is stopped, buttons are displayed that allow download of tracing files to
a local PC.

The Files and Folders section in /tmp/log contains a list of files in the corresponding /tmp/log directory.

To download it to a local PC, check the checkboxes located next to the required filenames and click the

Download

button.

To delete the specified files from the directory, click

Delete

.

4.1.14.3

Syslog Settings

The

SYSLOG

menu allows configuration of system log settings.

SYSLOG

is a protocol designed for transmission of messages on current system events. The gateway

firmware generates system data logs on operation of system applications and signalling protocols, as well as
occurred failures, and sends them to the SYSLOG server.

High debug levels may cause delays in device operation.
IT IS NOT RECOMMENDED to use the system log without a due reason.

The system log should be used only when problems in gateway operation occur and their reason
should be identified. To determine the necessary debug levels, please contact Eltex Service
Centre.

syslog

parameters specify IP address of the syslog server, the UDP port used to receive the syslog server

messages, and debug levels according to events and protocols.

Possible levels are as follows: 0—disabled, 1–99—enabled; 1—minimum debug level, 99—maximum

debug level.

Output the history of entered commands

—saves the history of

changes in gateway settings.



Server IP address

—the server address where the log of

entered commands is sent.



Server port

—the server port where the log of entered

commands is sent.



Detalization level

—verbosity level of the entered

commands log:

–

Disable logging

—disable generation of the

entered commands log.

–

Standard

—messages contain the name of the

modified parameter.

–

Extended

—messages contain the name of the

modified parameter as well as parameter values
before and after modification.

Syslog settings—

configuration settings of the system log.



Enable

—when checked, saves events log; otherwise,

logging is disabled.



Remote logging

—when checked, the system log is

stored on a server at the specified address.



Server IP address

—address of the server where the system log is stored.

«
...
108
109
110
111
112
...
»

Содержание SMG-2







































































































































































































Отзывы:

Нет отзывов