Eltek Valere Minipack, Быстрый старт и руководство пользователя

Страница: 18 / 40

Form 174-gb-
v2-
C
01_356808-103
_qstart-in
st-comm-o
pe
r_
minipack-p
ss_1v2
.docx_m
fm_2008-1
0-07
INSTALLATION CHECK LIST
System Data
Minipack P S S ystem
Minipack Power Supply System , type : Artic le No.:
Site, name:
Serial No.: Softw are, version No .: Rectifiers, ty pe & number of:
AC I nput Volt age, m easured: Batte ry Type: Batte ry Capacity: Inst allation carried o ut by, name:
Site Preparations
CARRY OUT FOLLOWING
:
OK
1. Organize the installation site
o
Prepare a 2U hig h spare location in existing 19”, 25 0 mm cabinet; C heck min. clearance: front access, 60 cm
o
Ensure the installation site is suitably ventilated a nd in a non-explosive atmosphere.
†
2. Prepare the installation t ools
o Check that insulated tools suitable for telecom installations are used
†
3. Prepare AC Supply: AC i nput cable(s) and fuses
o
Check the AC supply is the correc t t ype, an d that the ex ternal AC f uses and AC input cable(s) are s uitably rated
†
Mechanical Installation
Power is OFF!
CARRY OUT FOLLOWING
:
OK
4. Remove packaging and check equipment
o Check you have received all the parts and correct documentation.
o Inspect the equipm ent for phys ical damage (repo rt an y dam ages)
o Leave rectifier modules in their packaging or in t he selves, if factory installed. (commissioning task)
†
5. Remove the cabinet’s to p cover and dummy front panels
o
Check that cable entry from the to p is possible
o
Connection terminals are accesse s by opening the dra wer shelf
†
6. Position and fasten the subassembly
o
Subassemblies in existing 19” or in ETSI cabinets, using brackets, and 3ph AC Inpu t Connection Kit, if required
†
7. Mount the external batteries on the shelves
o
Start (if applicable) on the lower shelf first, and continue up wards
o
Do not term inate the batter y cable s yet !
†
8. Open the Minipack drawer shelf and lift the plastic cover
o
Unlock the upper and lo wer scre ws and slide the drawer shelf open, then lift the Melenex plastic cover
†
Electrical Installation
Power is OFF!
CARRY OUT FOLLOWING
:
OK
9. Make the system completely voltage free
o
Switch OFF or re move all load fuses (MCB1, MCBx), bat tery fuses (Fb1, Fbx) and extern al AC supply fuses
†
10. AC Connections
(or connect to the 3ph AC Kit)
o
Check AC configuration : Make available 3 single p hase mains feed and earth (PE)
o
Connect the AC Earth wire (PE) to the terminals AC Earth (PE)
o
Connect the AC input cable(s) to the terminals. Ca ble and terminal block labeling are to correspond
†
11. DC Connections
⎯
Load Circuits
o
Term inate DC Ea rth (T E): Common DC Output Ra il is connected to TE at onl y o ne place
o
For each DC load , connect one of the cables to the common DC out put terminal; the other to the fuse terminal
†
12. DC Connections
⎯
Alarm & Signal Circuits
o
Refer to you r s yst em’s connection dra wings and configuration, or t o the Quick Start Guide
o
Term inate Alarm Circuit cables to the relay output te rminals
o
Term inate Signal Circuit cables to the digital input/output terminals
†
13. DC Connections
⎯
Battery Cables Careful! Use correct polarity.
For each batter y shelf,
o
Mount 3 inter cell links to connect in series 4 battery blocks
o
Connect battery cables to fuses and Common Batter y, a nd to the shelf’s outer termi nals; (+) and (-)
o
Connect battery sym metry cables , if applicable, to the input terminals
o
Connect the temperatur e sensor cable , if applicable, to the D-Sub p lug or input termi nal, and fix the sensor (at th e
end of the cable) to a suitable place in the middle of the installed battery bank
†
Approval
Responsible of installat ion, sign.: Date: Approved by cu stomer, sign.:
EMC
regard
Electric
shock
Device
hazard
Electric
shock
www.elte kvalere.com
Hea dquarte rs:
Eltek Va lere
1303 E. A rapaho R d, R ichards on, TX. 75081, USA
Phone: +1 ( 469) 330- 9100 Fax: +1 (469) 3 30-9101
Eltek Va lere
Gråteru dv. 8, PB 2 340 Str ømsø, 3 003 Dram men, Norw ay
Phone: +47 32 20 32 00 Fax: +47 3 2 20 32 10