1. Cut off tip of caulk tube diagonally with opening
no larger than 1/8". Figure 27
2. Run a continuous bead of caulk at the seam
between the two parts. Figure 28
3. Smooth caulk gently with a wet fingertip. Figure 29
4. Using a clean rag, wipe off excess water and caulk.
Figure 30
INSTALLATION INSTRUCTIONS FOR SHOWER SEATS WITH
SWING DOWN LEGS
(This style seat has four (4) adjustable height legs)
Your seat with swing down legs is fully assembled.
Remove it from the box and proceed as follows:
1. Choose the height of the seat you want. Barrier Free
style showers will typically have fold up seat installed
at 17" to 19" height.
2. After selecting the height you desire, adjust each of
the four legs to that height while maintaining the seat
in a level position. Lock each of the lock nuts.
3. Place the seat against the wall of the shower
where you want the seat to be located. Seat may be
centered on the wall for a Barrier Free installation.
4. With the seat placed against the mounting wall,
position the two hinges to the wall. Using a pencil, mark
the three holes (3) holes in the flange onto the wall for
each hinge. Remove seat from wall.
5. Using a power drill with a 0.120" diameter drill through
the wall the three (3) mounting holes for each flange.
6. Apply silicone caulking around and inside each
drilled hole before installing the seat.
7. Place the seat against the mounting wall with each
hinge aligned to the mounting holes. Utilizing the six (6)
#10 x 2" Stainless Steel screws, place a Phillips screw
driver into your power drill and securely tighten each of
the six (6) screws.
THIS COMPLETES THE INSTALLATION OF THE SEAT
INSTALLATION INSTRUCTIONS FOR GRAB BARS
Recommended tools for installation:
1/4" Power Drill
1/8" drill bit when drilling through fiberglass
#2 Phillips Screw Driver and/or Phillips drill insert
1/2" Open end wrench or a small Crescent wrench
Tape measure
Pencil/pen
Center Punch
Silicone Caulk
1. As indicated earlier in this manual, wood
reinforcements must be solidly installed behind the tile
wall surface to provide a secure mounting surface to
attach the grab bars. Grab bars must be installed at
these locations only.
2. Select the particular size and style of grab bar you
want to install. Certain grab bars have snap in place
flange covers, and others have exposed flanges.
3. For grab bars with snap in place flange covers, use
the handle of a Phillips screw driver to tap back the
covers on the bottom edge of the covers. It will be
convenient in the installation process if the covers are
tapped together in the center of the grab bar.
Installation
Instructions
9
of
12
Materials Required:
Acrylic Latex Caulk
Wiping Cloths (Rags)
Clean Water
Cut off tip of caulk tube diagonally with opening
no larger than 1/8”.
(Figure 27)
Run a continuous bead of caulk at the seam between
the two parts.
(Figure 28)
Smooth caulk gently with a wet fingertip.
(Figure 29)
Using a clean rag, wipe off excess water and caulk.
(Figure 30)
12
Seam Caulking Instructions
Figure 27
Figure 28
Figure 30
Figure 29
Tools Required:
Caulking Gun
Cup
Your seat with swing down legs is fully assembled. Remove it from the box and proceed as follows:
(This style seat has four (4) adjustable height legs)
1.- Choose the height of the seat you want. Barrier Free style showers will typically have fold up
seat installed at 17” to 19” height.
2.- After selecting the height you desire, adjust each of the four legs to that height while
maintaining the seat in a level position. Lock each of the lock nuts.
3.- Place the seat against the wall of the shower where you want the seat to be located.
Seat may be centered on the wall for a Barrier Free installation.
INSTALLATION INSTRUCTIONS FOR SHOWER SEATS
WITH SWING DOWN ADJUSTABLE LEGS
4.- With the seat placed against the mounting wall, position the two hinges to the wall.
Using a pencil, mark the three holes (3) holes in the flange onto the wall for each hinge.
Remove seat from wall.
www.ellasbubbles.com
Page 13 11/13
