background image

Radio

Adapter

Pag. 4/12

1.3 - CIRCUIT DIAGRAM

Power Supply

TTL

10

11

TTL

TTL

TTL

RadioKey

RadioAdapter

RS-485

TTL

RadioKey

Power

Supply

A

B

C

}

NOT for

FCC models

TERMINALS

Radio

Key  Connector to connect the 

Radio

Key

TTL 

TTL serial port to connect directly to devices

7-8-9 

RS-485 serial port to connect directly to devices or to the

                     monitoring system
                     (on in 

Radio

Adapter /S models)

10-11 

Power supply 100...240V

a

SMA connector for external antenna

                     (only on 

Radio

Adapter EXT models)

Cable for external antenna (length: 1m)

External antenna

IMPORTANT

: For RadioAdapters with an external antenna, use Eliwell

                         supplied cable and antenna only.

IMPORTANT

! Do not touch the SMA connection

        

     for external antenna (A) as static

       

     electricity may have built up!

1.4 - MECHANICAL ASSEMbLY

This device is designed to be wall-mounted or on a DIN rail.
The ambient temperature range for correct operation is -5 to 60°C, and the permitted humidity range is 10 to 90% (non-condensing).
Sufficient ventilation should be provided if the device is installed inside an electrical panel or switchboard.
Do not install the device in damp or dirt-laden areas.

1.5 - INSTALLING THE ANTENNA (NO FCC MODELS)

The antenna can be inserted straight into the 

Radio

Adapter connector or panel-mounted and connected to 

Radio

Adapter using 

the cable supplied in the Antenna kit.

N.b.: The panel that the antenna is mounted on must be no more than 3mm thick.

For the panel mounting of the antenna, please follow the proceduredescribe below:
ANTENNA KIT COMPONENTS:
 

- 1m cable

 

- a SMA 90° connector

 

- Seal ring, nut and washer to fit the cable to SMA 90° connector

- Drill a hole in the panel as

  shown in Figure 1:

6.8 mm

7.2 mm

- Tighten the nut to firmly clamp

  the cable (see Figure 3)
- Rub some more thread locker

  onto the connector as shown

  in Figure 3

max 3 mm

Washer

Threadlocker

O-ring

Panel

Nut

Connettor 

SMA 90°

- Fit the seal ring (o-ring) to the

  end of the cable to be fitted to 

  the panel (see Figure 2)
- Insert the end of the cable to be

  fitted to the panel through the

  previously drilled hole.
- Slip the washer over the end of

  cable pushed through the hole

  (see Figure 2).
- Rub a little thread locker onto

  the connector as shown in

  Figure 2.

max 3 mm

Washer

Threadlocker

O-ring

Panel

Nut

- Tighten the SMA 90° connector

   and fit it to the antenna (see

   Figure 4)

NOTE:  LOCTITE® 243

             threadlocker is

             recommended.

max 3 mm

Washer

O-ring

Panel

Nut

Connector

SMA 90°

Fit the antenna

Figura 3

Figura 2

Figura 1

Figura 4

Содержание RadioAdapter













Отзывы: