background image

EWHT800LX  

 

2 - EN

English

INTRODUCTION

The Coldface EWHT800LX series controls the temperature and humidity of a static or ventilated cold 

room. The curing cycle consists of 1 program with 8 customisable climate profiles. The instrument 

controls positive and negative cold rooms and is capable of managing a double evaporator and con-

denser probes. Coldface has 8 configurable relays, 4

 

low-voltage digital inputs configurable for door 

switch,

 

alarm and pressure.

 

Models are available with clock with yearly calendar and HACCP event 

logging. The instrument can be connected to Televis

System

 via the optional plug-in module. The box 

allows for installation of a power contactor or a disconnecting switch with door lock. 

This summary document contains basic information about the standard models EWHT800LX. For fur-

ther  information  and  different  configurations,  refer  to  the  complete  user  manual  p/n  9MA10024 

which can be downloaded free of charge from the www.eliwell.it website.

MECHANICAL INSTALLATION

Manual 

defrost

Display 

 HACCP alarms 

if function active

Display alarms

if active

Functions menu

LOC keyboard lock

rSE activate reduced Set

rPA Pressure switch alarms

rEd disable HACCP

rHC reset HACCP alarms

nAD Day/Night

Aut Automatic regulation

St Start Climate Profile

rSt Reset Climate Profile

System

info

SP1

-18.9

rtc

18.55

Pb1

-20.6

set

time and date

display

probe values

display

probe values

modifty

SetPoint value

confirm with

1 sec

1 sec

1 sec

3 sec

3 sec

ON / OFF function

Pb2

-20.6

InS

USR

PAr

LitE

SEt

0.0

see manual

see manual

diF

2.00

HSE

50.0

modify

value

confirm

with

SetPoint & Probes

Parameters

NAVIGATION DIAGRAM

• 

Screw the backplate to the wall 

using 4 screws (not supplied) to 

match the holes A...D.

• Shut the door and cover the 

screws with the corresponding plate

• Drill holes in the top (or bot

-

tom) of the backplate to pass the 

high and low-voltage wires through.

Cable clamps must be no bigger 

than size PG29

• Remove the protective plate 

on the right of the door

• Take out the 2 screws supplied 

and then open the cover.

Содержание Coldface EWHT800LX Series
















Отзывы: