10
Mounting
Before beginning installation:
•
Check that the product purchased is of a suitable size for
the chosen installation area.
•
Remove the charcoal (*) filter/s if supplied (see also
relative paragraph). This/these is/are to be mounted only
if you want lo use the hood in the filtering version.
• Check (for transport reasons) that there is no other
supplied material inside the hood (e.g. packets with
screws (*), guarantees (*), etc.), eventually removing
them and keeping them.
Expansion wall plugs are provided to secure the hood to most
types of walls/ceilings. However, a qualified technician must
verify suitability of the materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong enough to take
the weight of the hood.
Do not tile, grout or silicone this appliance to the wall.
Surface mounting only.
Only for some models
An aesthetic flue can be purchased as an optional accessory.
Check with the authorized dealer whether the model in your
possession envisages this possibility.
We advise installing the hood after having purchased the flue
to check with certainty the most suitable installation.
Fig. 5
•
Apply three adhesive strips
C
to the back of the hood.
If necessary (in the case of walls not perfectly
perpendicular or in the presence of walls partly covered
with tiles) apply two
D
spacers in correspondence with
the definitive fixing holes (click fixing).
•
Trace a centre line on the wall to facilitate the montage
(1)
, position the hole template so that the middle line
printed on it corresponds to the centre line previously
drawn and that the lower side of the grill corresponds to
the lower part of the hood once mounted
(2)
.
•
Make two holes with the 8 mm Ø drill and fix the support
bracket with two dowels and wall screws
(3)
.
•
Open the steam screen and remove the grease filter (see
relative paragraph).
• Hang up the hood
(4)
, adjusting its position
(5-6)
and
from the inner part of the hood mark two points for the
definitive fixing
(7)
. Remove the hood and make two 8
mm Ø holes
(8)
, insert two wall dowels, hang the hood up
again and fix it definitively with two screws
(9)
.
• Connect the electricity
(10)
, but leave the hood
disconnected from the general electric panel of the
house.
•
If the hood is to be used in the suction version, install the
flange supplied in the kit on the exit hole of the hood
(
11A
- suction version – also install a fumes discharge
tube of suitable dimensions) instead of the deflector (
11F
– filtering version
).
•
Mount the grease filter and close the steam screen.
Attention!
If the hood is to be used in the suction
version, remove, if supplied with the kit, the carbon filter
and the fixing rods (on the back of the grease filter – see
relative paragraph).
If the hood is to be used in the filtering version, check
that the carbon filter is already mounted on the back of
the grease filter or, in its absence, purchase it and install
it.
•
Connect the hood to the general electric panel.
Description of the hood
Fig. 1
1.
Control panel
2.
Grease filter
3.
Grease filter release handle
4.
Lighting
5.
Vapour catcher
6.
Air outlet
7.
Telescopic chimney
The steam screen must always be left closed and opened only
for maintenance (e.g. cleaning or changing filters).
Operation
To select the functions of the hood just touch the commands.
Light key ON/OFF
Intensive speed selection key
(suction
power) - duration 5 minutes - press again to
return to previous setting.
High-speed selection key
(suction power).
Medium-speed selection key
(suction power)
- when flashing it indicates the need to wash or
replace the carbon filter. This signal is normally
deactivated. To activate the alarm, disable the
electronic by pressing the
0
button for 3
seconds.
Next, simultaneously press buttons
1
and
2
for
3 seconds; at first, only button
1
will flash, then
both buttons
1
and
2
will flash to indicate
activation. Repeat the procedure to deactivate
the alarm; at first buttons
1
and
2
will flash and
subsequently only button
1
to indicate
deactivation.
Low-speed selection key
(suction power) –
when flashing it indicates the need to wash the
fats filter.
Motor key OFF
(stand by) – excludes the
electronics – reset wash/replace filters signals.
MOTOR OFF
Press briefly to switch the motor off.
RESET FILTERS SIGNALS
