Elektron Analog Four MKII Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 108

Elektron Analog Four MKII Скачать руководство пользователя страница 61

12 GLOBAL SETTINGS MENU

61

POLARITY selects the polarity of trig signals sent. V-TRIG and S-TRIG options exist. V-trig (volt-

age trigger) is a trig pulse going from 0 V to a user-defined voltage level. S-TRIG (short circuit

trigger) goes the other way, from a user-defined voltage level to 0 V. V-TRIG is the most common

trig polarity. S-TRIG is primarily used by older Moog, Korg and Yamaha synths.
LEVEL selects the level of trigs sent, measured in volts. The standard logic level of +5 V is

enough to trig most equipment, but some might need higher voltages to react.

GATE

gives a longer pulse, with a duration of the whole note length.

POLARITY works as the same parameter available when TYPE is set to TRIG.
LEVEL works as the same parameter available when TYPE is set to TRIG.

CLOCK

will send periodical pulses with a period synced to the sequencer step length.

CLK sets the clock division of the pulse.

12.6.2 VOLTAGE TRIM

It is possible to trim the CV out voltage levels. These settings are stored in the machine without being

connected to any specific Project. Adjusting these values is mainly useful if you wish to send pulses with

very exact voltage levels or to generate very specific voltages as a linear value and if you believe that the

factory trim of the Analog Four MKII or the external machine is off.

Make sure you have a good voltmeter before proceeding. Connect a TRS cable to the output you want

to trim. Connect the voltmeter’s negative terminal to the sleeve of the connector. Connect the positive

terminal to the tip of the connector.

Each CV output has three trim settings. Begin by selecting 0 V, then press and hold the

[YES]

key. 0 V is

output as long as

[YES]

is held down. Use

[ARROW]

keys

[LEFT]

/

[RIGHT]

or

DATA ENTRY

KNOB A

to

adjust the voltage until your voltmeter shows exactly 0 V. Repeat the process for both 8 V settings (the

first one is for continuous voltage, the second is for pulse).
Note that adjusting the CV does not improve CV pitch control. If you have set up pitch control of an ex-

ternal synth properly then, any linear error has already been compensated for by that calibration. In fact,

you will have to reconfigure the CV pitch control after changing the values in the VOLTAGE TRIM Menu,

because you will have changed the point of reference.

12.7 VOICE ROUTING

This menu item accesses the global routing of the four voices.

«
...
59
60
61
62
63
...
»

Содержание Analog Four MKII













































































































Отзывы:

Нет отзывов