manualshive.com logo in svg

eledo Luno5, Руководство пользователя, Страница: 9 / 16

Поделиться
Скачать
eledo Luno5 Скачать руководство пользователя страница 9

 

 

Luno5 light switch manual  

 

 www.eledo.pl   

 

           9 

Additional advanced options  
 
 

5. 

Programming.

 

 

The Luno5 device is factory-programmed and is ready to work. If required, you can change some of its functions depending on 

user needs and preferences. 

You can program following elements: 
 

1. 

turn children count on (ones that reach only bottom direction sensors). 

2. 

change the conventional direction of entrance/exit to the opposite one. 

3. 

automatically turn lights on after dark. 

4. 

turn off function of switch sounds used after automatic turning lights off. 

5. 

turn off function of automating switching lights off after dawn (granted that the light was on at least for 8 hours) 

– default 

it’s on. 

6. 

function 6 together with function 7 sets the time of automatically turning the lights off when no user goes through the door 

for a particular period of time. The light will be off after 30 / 60 minutes or after 4 hours from the time of when a person 
enters a room. Function 6 alone (30 minutes), function 7 alone (60 minutes), functions 6 and 7 together (4 hours). 

7. 

function 7 sets time together with function 6 (as above). 

8. 

change the time of the automatic switching lights off after a longer push of the  

„ ” button from 30 sec. to 3 min. 

 

To change (program) functions you need to 

– with the device powered on: 

-  push and hold both buttons 

„ ” 

and 

„

”

 

-  after a while release 

„

”

 button and keep pushing 

„ ” 

button 

-  button 

„ ”

 needs to be pushed for about 20 seconds until the display illuminates (digit 0). 

- after the display with digit 0 illuminates, you need to release the 

„ ” 

button, (we

’ve entered programming options, the display 

flashes quickly)  

-  button 

„ ”

  needs  to  be  pushed  few  times,  depending  on  a  number  of  functions  that  we  want  to  program 

– according to the 

further description.  

- after multiple pushes of the  

„ ” button, the display will show the proper function number. Turning particular function on and off 

is made by the alternant push of the

 

 

button

. 

 

1)

  if  we  shortly  push 

„ ” button once (display will show 1) then we will enter a mode of turning on/off children count function 

(counting from bottom motion sensors). The device do

esn’t count children by default. If the button 

 is illuminated it means that 

function is on. Pushing 

 button (auto/manual) will turn this option on or off. If you have no children then we recommend turning 

this option off to avoid increase cases of people miscounts. 

2)

 if we shortly push the 

„ ” button twice then we will enter the mode of turning on/off functions of the changing entrance/exit 

direction to the opposite one. If the hand symbol is illuminated it means that the function is on. The function needs to be turned off 
when the device works conversely, ie. lights turn on when we leave the room. 

3)

 if we shortly push 

„ ” three times then we will enter a mode of turning on/off the function of auto turning lights on in a room. It 

will automatically turn on lights if the room goes dark for five seconds. If someone is inside (people register shows more than 0). If 
hand symbol is illuminated it means that the function is on. The function is off by default. 

4)

 if we shortly push 

„ ” four times then we will enter a mode of turning on/off function of generating sound during turning lights 

off. If hand symbol is illuminated it means that sounds are off. The sound is on by default. 

5)

 if we shortly push 

„ ” five times then we will enter a mode of automatically turning the lights off after dawn and 8 hours of 

constantly being on without any user door activity. If for 8 hours no-one goes through the doors and the lights inside the room are 
still on, then after 8 hours the device will check if the room is light by temporary turning lights off. If after temporary turning lights off 
the room is still bright (e.g. day comes) then the unnecessary light will be turned off. If the hand symbol is illuminated it means that 
the function is off. The function is on by default 

– this enables automatically turning unnecessary lights off. 

6) 7)

 if we shortly push 

„ ” six times then we will enter a mode of turning on or off the function of turning the lights off. Turning 

this  function  on  enables  automatic  turning  lights  on  after  30  minutes  of  lack  of  user  activity  (lack  of  going  through  doors). 
Additionally when the Luno5 device has a motion sensor connected then turning function 6 on enables turning lights off after 30 
minutes  from  last  motion  sensor  activity.  Time  of  automatically  turning  lights  off  can  be  extended  to  60  minutes  by  turning  the 
function 7 on instead of function 6. 

If we’ll turn both functions on then lights be turned off after 4 hours from last time when a user 

goes through the doors. The function of turning lights off (30 or 60 minutes) can be turned off when the device is mounted e.g. in 
the  bathroom  where  peo

ple don’t spend much time. Turning lights off after 4 hours is useful when the device is mounted in the 

room. If users fall asleep with the lights on then after 4 hours from entering the room the lights will turn off. Turning lights off after a 
specified time of lack of activity (30 and 60 minutes) also cause the reset of the people register.  

If the hand symbol is illuminated it means that the function is on. As distinct from function 5 the device turns lights off regardless 

of the room being dark or light. The function is off by default. 

Содержание Luno5

















Отзывы:

Нет отзывов