Electrolux Inspiration EWX11831 TC3 Скачать руководство пользователя страница 63

Страница: 63 / 71

Guide to diagnostics of EWX11831 electronic controls

2013 TS/DT-mdm FCPD-dp

63/71

599 77 00-82 Rev. 01

Checks to perform:

EF1

EF1: Drain hose blocked/kinked/too high; drain filter clogged/dirty

EF1

EF2

EF2: Excessive detergent dosing; drain hose kinked/blocked; drain

filter dirty/clogged

EF2

EF3

EF3: Aqua Control device triggered

EF3

EF4

EF4: Water fill pressure too low and solenoid valve open

EF4

EF5

EF5: Unbalanced load, spin phases skipped.

EF5

This warning only appears at the end of the cycle. The appliance detected long drainage

phases during the cycle. (E.g.: More than 20 seconds when draining after rinses). Check/clean

the drain filter.

This is an excessive detergent dosing warning. The system detected too much foam was forming during

the drain phases. Advise the Customer to use the correct quantity of detergent and to make sure the

filter and drain circuit are clean.

This warns about the presence of water at the bottom of the appliance. Check for any water leaks and

that the Aqua Control device float is positioned correctly.

Or caused by excessive overheating of the drain pump. Check for any items which may obstruct the

normal operation of the rotor.

This is an unbalanced load warning. The appliance detected an extremely unbalanced load

during the spin phases. Advise the customer to load more washing into the drum and not just individual

garments.

Check that all the connectors are correctly inserted

It is a warning that the water pressure is too low. If the water pressure is connect, check:

the wiring of the flowmeter and the Flowmeter.

Check that all the connectors are correctly inserted

If there are burns on the circuit board,

see page 69

Содержание Inspiration EWX11831 TC3








































































Результаты поиска

Содержание Inspiration EWX11831 TC3

Отзывы:

Бренды по названию

Популярные бренды

Electrolux Inspiration EWX11831 TC3, Руководство по обслуживанию

Результаты поиска

Содержание Inspiration EWX11831 TC3

Отзывы:

Бренды по названию

Популярные бренды