Electrolux Inspiration EWX11831 TC3 Скачать руководство пользователя страница 16

Страница: 16 / 71

Guide to diagnostics of EWX11831 electronic controls

2013 TS/DT-mdm FCPD-dp

16/71

599 77 00-82 Rev. 01

Alarm

Description

Possible fault

Machine status/action

Reset

Page

E87

Display board microprocessor faulty

If this continues, replace the display board

No action to be taken

START

ON/OFF

RESET

E91

Communication error between main
PCB and display

Wiring faulty; Control/display PCB faulty, Inverter board faulty,
Weight sensor board faulty, Main PCB faulty.

---------------- RESET

E92

Communication inconsistency
between main PCB and display
(incompatible versions)

Incorrect control/display PCB
Incorrect PCB (does not correspond to the model).

Cycle blocked

ON/OFF

E93

Appliance configuration error

Main PCB faulty (incorrect configuration data);

Cycle blocked

ON/OFF

E94

Incorrect configuration of washing
cycle

Main PCB faulty (incorrect configuration data);

Cycle blocked

ON/OFF

E97

Inconsistency between programme
selector and cycle configuration

Main PCB faulty (incorrect configuration data).

Cycle blocked

RESET

E98

Communication error between main
PCB - Inverter

Incompatibility between main PCB and Inverter

Cycle blocked

ON/OFF

E9C

Display board configuration error

Display board faulty

----------------

START

ON/OFF

RESET

E9E

Display board sensor/touch key
faulty

Display board faulty

----------------

ON/OFF

EC1

Solenoid valve blocked with
operating flowmeter

Wiring faulty; Solenoid valve faulty/blocked, Main PCB faulty,

Cycle stops with door locked

Drain pump continues to operate (5 min.

on, then 5 min. off. etc.)

RESET 62

EF1

Drain filter clogged
(drain phase too long)

Drain filter clogged/dirty.
Drain hose blocked/kinked/too high.

Warning displayed at the end of cycle. START/RESET

EF2

Overdosing of detergent
(too much foam during drain
phases)

Excessive detergent dosing; Drain hose kinked/blocked;
Drain filter clogged/dirty.

Warning displayed after 5 attempts or

by the specific LED.

RESET 63

EF3

Aqua control system intervention

Water leaks onto base frame; Aqua control system faulty.

Appliance drain

ON/OFF RESET

EF4

Water fill pressure too low, no signal
from flowmeter and solenoid valve is
open

Tap closed, water fill pressure too low

----------------

RESET

EF5

Unbalanced load

Final spin phases skipped.

----------------

START/RESET

EF6

Reset

If it continues, replace the main board.

No action to be taken

----------------

EH1

Appliance power supply frequency
out of limits

Problem with the power supply network (incorrect/disturbed);
Main PCB faulty.

Wait for nominal

frequency conditions

ON/OFF 64

EH2

Supply voltage too high

Problem with the power supply network (incorrect/disturbed);
Main PCB faulty.

Wait for nominal

voltage conditions.

ON/OFF 64

EH3

Supply voltage too low

Problem with the power supply network (incorrect/disturbed);
Main PCB faulty.

Wait for nominal

voltage conditions.

ON/OFF 65

EH4

0Watt relay malfunction

Main circuit board faulty.

----------------

ON/OFF

RESET

Содержание Inspiration EWX11831 TC3








































































Результаты поиска

Содержание Inspiration EWX11831 TC3

Отзывы:

Бренды по названию

Популярные бренды

Electrolux Inspiration EWX11831 TC3, Руководство по обслуживанию

Результаты поиска

Содержание Inspiration EWX11831 TC3

Отзывы:

Бренды по названию

Популярные бренды